CC2530: Stop device from listening to commands sent by coordinator
Part Number:CC2530Hi,I wanted to know what lines of code I could use to make the CC2530 stop listening to the coordinator (stop doing commands sent by coordinator)? Also what lines of code would make...
View ArticleCompiler/TMS320C5505: fir filter dsplib
Part Number:TMS320C5505Tool/software: TI C/C++ CompilerDear All,I am trying to use the built-in cfir function in dsplib to implement the fir filter. I am using below code:Int16 left_input;int const...
View ArticleClik here to view.
CC1310: TI 15.4 -STACK application cannot run while open the bootloader backdoor
Part Number:CC1310Hi:I have run the TI 15.4 Stack application(TIMAC 2.0, simplelink_cc13x0_sdk_1_30_00_06) successful on my boards(SMARTRF06+CC1310-7XD-7793).Actually it didn't run well at the...
View ArticleCC2640R2F: power supply ripple requirment.
Part Number:CC2640R2FHi, what's the ripple requirment of the power supply?especially during the Flashing? will it impact the programming flash?BR. Albin
View ArticleTLV320AIC3206: Line inputs present on this codec to connect my microphones
Part Number:TLV320AIC3206Hi I have designed a sound card based on TLV320AIC3206. Can I use Line inputs present on this codec to connect my microphones??if yes the please suggest the register settings...
View ArticleCC2640R2F: reset signal vs. VDD sequence.
Part Number:CC2640R2FHi, is there a timing requirment between ResetN vs. VDD sequence? thanks. BR. Albin
View ArticleClik here to view.
BQ28Z610: Learning cycle of Bq28z610 using GDK and Evaluation module of Bq28z610
Part Number:BQ28Z610Hi Team,I am trying to use GDK for learning cycle of BQ28z610 along with evaluation module of Bq28z610. I made hardware connection as described in User Manual of GDK.Please refer...
View ArticleUCC25630 OVP BW PIN ISSUE
I have four questions on ucc25630 as follows:When the FB pin pull Low, will shut dow, when the Low situation is released, the reply time for how long(?us)? BW pin When OVP fault, the...
View ArticleClik here to view.
DP83867IR: For crystal input level
Part Number:DP83867IRHi team, The level on the XI pin of DP83867 is observed as 3.2Vp-p. Is it okay or not? There is not detailed spec for crystal in the datasheet.Thanks,Sam Lee
View ArticleTLV320AIC3206: getting some noise while recording audio
Part Number:TLV320AIC3206Hi I have designed a sound card based on tlv320aic3206. I am getting some noise while recording audio even when I am not connecting any headset on mic input . DAC output in...
View ArticleTMS320F28069: C2000Ware update plan for powerSUITE
Part Number:TMS320F28069Hello, TI Experts, Our customer sent us a question about C2000Ware.They found "powerSUITE is not included in C2000Ware" in "Table 1. controlSUITE to C2000Ware Root...
View ArticleTPS54429: About impedance of EN pin
Part Number:TPS54429Hi Team, Our customer would like to know the impedance of EN pin.I understand that TPS54429 has not pull-up or down resistor for EN pin so it is High impedance.Is my understanding...
View ArticleCCS/TMS320F28335: Warning: The configured device (TMS320F28335), does not...
Part Number:TMS320F28335Tool/software: Code Composer StudioHello,I'm working with my device which is supported by a third party. The platform is CCSv5. This is the first time I try to burnprocess and...
View ArticleClik here to view.
LM5060: Current Limit Function
Part Number:LM5060Hi Team,I would like to ask about the following red part "Current Limit Function Enabled: Startup Only".Does it mean current limit is enabled only during...
View ArticleLinux/DRA746: When should I use IH264VDEC_Params instead of IVIDDEC3_Params?
Part Number:DRA746Tool/software: Linuxviddec2test.c uses IVIDDEC3_Params, but dce_test.c uses IH264VDEC_Params.for usual decoding, IVIDDEC3_Params is enough, right?only when we request some special...
View ArticleBQ76930: CELL voltage is quite accurate, but pack voltage has a big error.
Part Number:BQ76930I use BQ76930 to protect 10 serial LI-battery. When reading individual cell, the voltage error is only 2mV,each cell voltage is around 4.000V. So the pack voltage should be around...
View ArticleCC2640: Radio wave trend changes depending on temperature
Part Number:CC2640I am currently using a CC2640 PCB connected to a Bluetooth tester with a coaxial cable.From the PCB, I am transmitting 3dbm, 4dbm, and 5dbm Bluetooth signals to the Bluetooth tester.I...
View ArticleClik here to view.
ISO1540: about ICC1 and ICC2
Part Number:ISO1540Hi,I am checking the current consumption of the device.I saw variations in the current consumption of the data sheet, but there is no MIN data.Is there data on the following...
View ArticleAWR1642BOOST: Can we use the postproc to do some coustom process. or parse...
Part Number:AWR1642BOOSTI read the radarstudio user guide. i just see that postproc do some proceess the software contain. I wonder if we can do some coustom process or parse the raw adc bin file in...
View Article66AK2H14: Clock synthesizer filtering used in EVB
Part Number:66AK2H14Hi,In K2E and K2H EVBs, for filtering power for clock synthesizers, NFM18CC222R1C3 is used ( 3 termianal cap) instead of normal ferrite bead.I would like to know if there are any...
View Article