CC3200MODLAUNCHXL: Using a k-type thermocouple with the ADC example from the...
Part Number:CC3200MODLAUNCHXLHello All,Could anyone here offer guidance on connecting a 2-wire k-type thermocouple to the Launchpad? I found an ancient thermocouple here in the office that I would...
View ArticleClik here to view.
CC2640R2F: ADCBufCC26XX occasionally pends indefinitely in one-shot/blocking...
Part Number:CC2640R2FHi Texas Instruments team & community, I'm observing the ADCBufCC26XX driver hanging up and pending indefinitely when used in one-shot, blocking mode for a single sample...
View ArticleBQ25892: Charge current (ICHGR) does not match actual current in warm and...
Part Number:BQ25892Hi,When temperature is at "TS WARM" or "TS COOL", the "ICHRG" don't correspond to real current of charge. The current presented by the "ICHRG" is much higher than in reality.Some...
View ArticleInterfaces
What is the minimum hardware that I need in order for the chip to be working? I want to use these as Bluetooth transceiver units. Is just proving power to the chip sufficient enough?
View ArticleUC2909-EP: Pin and functionality compatible with UC3909DW?
Part Number:UC2909-EPHi,I have a customer that is currently using the UC3909DW in their design but the device has been reported to be no longer available. They are looking at using the UC2909-MDWREP...
View ArticleCCS/EK-TM4C1294XL: Difficulty setting PWM clock correctly using recommended...
Part Number:EK-TM4C1294XLTool/software: Code Composer StudioHello all,So this is a problem with a couple of twists for me:In the code attached, I'm attempting to generate a simple PWM servo-type...
View ArticleCC2640: How to detect cc2640 is wake up from Power shutdown?
Part Number:CC2640Hello,I want to detect the shutdown of cc2640 using reset line.I tried following:uint32_t rSrc = SysCtrlResetSourceGet(); if(rSrc == RSTSRC_WAKEUP_FROM_SHUTDOWN) {}But this condition...
View ArticleMSP430F2013: Analog input (SD16)
Part Number:MSP430F2013I'm using MSP430F2013 to get analog input voltage. It use SD16 and save count value in SD16MEM0 every 0.256ms . It stop working after few months running. When I plug in MSP430...
View ArticleCC2650: Sensor Controller COMPA Settling Time
Part Number:CC2650Hello,I'm using the CC2650 chip with the Sensor Controller to measure COMPA cross over against a custom voltage reference and am trying to debug some odd behavior.In the sensor...
View ArticleLMH1218: Cascading multiple LMH1218 and jitter
Part Number:LMH1218Hello,We are hoping you could help us check into a concern that we have with our new design. Currently we have a requirement for three SDI outputs and are using three LMH1218...
View ArticleTINA/Spice/LM7321: Pin Mapping of PSPICE model?
Part Number:LM7321Tool/software:TINA-TI or Spice ModelsMaybe I'm missing something, but shouldn't the model file for the LM7321 have comments mapping the SPICE pins to the IC pins? Something like this...
View ArticleRTOS/CC2640R2F: Getting started with TI RTOS and custom hardware
Part Number:CC2640R2FTool/software:TI-RTOSSo today my protottypes of a design using the CC2640R2F came in the mail and i was very pleased that things seem to be working as expected. I can upload code...
View ArticleTHS4131: Pin 7 - May I connect to V+?
Part Number:THS4131Is there any problem if I connect pin 7 to V+? That way I may use THS4130 in the same position (should I need it) without concerns about leaving PD pin open. I know PD may be left...
View ArticleClik here to view.
CCS/TM4C123GH6PM: PROBLEM IN THE GPIO INTERRUPT
Part Number:TM4C123GH6PMTool/software: Code Composer StudioHi,Once again thanks for all the people in the community for their support. I am facing a problem in the GPIO interrupt. I am working with the...
View ArticleCC1350: Prop Mode 100 kbps Occupied Bandwidth
Part Number:CC1350Does anyone know what the occupied bandwidth for Prop mode 100 kbps is? I can find such information for Prop mode 5 mbps in CC2650 data sheet, and I can't find it anywhere for CC1350....
View ArticleClik here to view.
Help with Keil settings and Tiva C Series Launch Pad
HiI am using Tiva C Series TM4C123G LaunchPad Evaluation Board with TM4C123GH6PM Microcontroller.My IDE is Keil and the debugger doesn't start and the code is stack before executing the main.My...
View ArticleTMS320F28027: Flash Status 30 error
Part Number:TMS320F28027Hello, I am not sure why I am not able to get a status value of 0 when i write something to my flash. I can see the memory address change to my specified value. However I am not...
View ArticleStarterware/BQ25570: ultrasonic generator box 15 khw
Part Number:BQ25570Tool/software: StarterwareI HAVE ULTRASONIC GENERATOR BOX HAVING TEN TRANSISTOR 2SC 5570 TRANSISOR BUT ALWAYS PROBLEMS IN CIRCUIT MY EMAIL ID moryanirajkumar1@gmail.com SOME TIME...
View ArticleCCS/TMS320C6678: Can I includ two linker files??
Part Number:TMS320C6678Tool/software: Code Composer StudioHi,I've got TMS320C6678 board and I want to join two programs.My first program is a example code about "timer" programing. Well, I don't have...
View ArticleCC1120: CC1120 current consumption at 2.1V
Part Number:CC1120Hi TI, Do you have the current consumption numbers for TX at +10 dBm and 0 dBm at 2.1 V and the RX consumption number at 2.1V ? We need this info to decide whether to use the...
View Article
