C2000 PIN MUX UTILITY FOR PICCOLO F2807x
Hi,is there a Pin Mux Utility version for F2807x Piccolo device?Thanks
View ArticleADC12J4000EVM: Instructions: How to use ADC12J4000 with High Speed Data...
Part Number:ADC12J4000EVMI do not have a question but I want to make a writeup of my work in the last weeks in order to help others achieve the same results much quicker.Jim Seton from TI was kind...
View ArticleClik here to view.
RTOS: Task of lower priority added to stack is not allowing higher priory...
Tool/software: TI-RTOSOddly the task module is not stacking tick time slots for each task this case a lower priority task has a [while(1)] loop. The only other unique aspect is (~.IdleTask) was created...
View ArticleCC3200MODLAUNCHXL: Is Energia support CC3200 APIs ?
Part Number:CC3200MODLAUNCHXLHello,Can I use CC3200 based APIs/commands in Energia IDE? if Yes, then which programming language supported by Energia?Regards,Pratik
View ArticleLinux/AM5728: Custom board detection via SD Card boot (u-boot)
Part Number:AM5728Tool/software: LinuxHi,I have a question about AM572x Processor Linux SDK.My customer are trying to boot there AM572x custom board via SD card which includes the pre-build u-boot and...
View ArticleClik here to view.
BQ24610: BQ24610 Application Question
Part Number:BQ24610Hi Sir,May I know our BQ24610 can support hot-plugged when battery is connected to charger? because our competitor LinearTech LTC4006 can.And if you have best solution, please advise...
View ArticleCC1310: SET_CCFG_IMAGE_VALID_CONF_IMAGE_VALID register
Part Number:CC1310Hi,Trying to do a custom bootloader in the memory page 31 as the bim_oad_offchip example.In the example the register SET_CCFG_IMAGE_VALID_CONF_IMAGE_VALID is set to 0x1F000 ( page 31...
View ArticleMSP430FR5738: MSP430FR5738 ADC10_B internal voltage divider value and accuracy
Part Number:MSP430FR5738Hi MSP Team,a customer is asking for the value and accuracy of internal voltage divider which is used in ADC10_B of MSP430FR5738 to measure (AVCC-AVSS)/2. Can we share any...
View ArticleCC1190: AN119
Part Number:CC1190Hello! In the example AN119 (Using the CC1190 Front End with CC1100E in the 470 MHz-510 MHz band) not distinguishable component values. Help with nominal values scheme?
View ArticleClik here to view.
CCS: ILLEGAL OPCODE ERROR
Tool/software: Code Composer StudioI've created a simple project in code composer in assembly in which I take some data from a buffer, some filter coefficients from another buffer and then do the...
View ArticleIS the DLP NIRscan for solid samples (plant, soil, crop samples) ?
Is the DLP NIRscan relevant for the analysis of solid samples (plant, soil, crop samples) ?Thanks for your answer
View ArticleLinux/AM3359: CAN bus goes into ERROR-PASSIVE state after connecting it to...
Part Number:AM3359Tool/software: LinuxHello there,I have been able to setup a CAN bus ( with CAN0 and CAN1) by making one sending and the other receiving without problems../ip link set can0 up type can...
View ArticleClik here to view.
Linux/AM5728: Exception being thrown in Linux when manually triggering a GPIO...
Part Number:AM5728Tool/software: LinuxHi Pavel,Your suggestion to fix the problem in the post worked for me. Thanks very much. I configured GPIO2 similarly. I then configured GPIO2_2 as input and am...
View ArticleClik here to view.
BQ27742-G1: BQ27742-G1 Fuel Gauge Issue
Part Number:BQ27742-G1Hello Team,We are monitoring battery health by BQ27742-G1 Fuel Gauge. (Battery specification - 3.7VDC, 4600mAH, Li-Ion battery)and we are writing listed below parameter in...
View ArticleBidirectional Communications and Power
Hello,I have an application where I need to transfer a small amount of power over a wireless link (1W or less) while at the same time allowing for bidirectional communication. Can someone please point...
View ArticleCCS/TMS320C6657: What's the macro flag for C6657 in CCS
Part Number:TMS320C6657Tool/software: Code Composer StudioIn some CCS example projects, I saw "#if defined(_TMS320C6400)" or "#if defined(_TMS320C6740)" , but I'm looking for a macro flag for...
View ArticleClik here to view.
LM2736: LM2736, voltage drop with high load
Part Number:LM2736I used Texas Webench to design a power supply with an LM2736 (see attached). The regulator is supplying an MCU and some sensors. The board also has an LCD with a tipical consumption...
View ArticleCC2538: default response enable with zcl_SendReportCmd()
Part Number:CC2538Hi to All, I'm using CC2538, IAR, Smart Energy.We use a router to send a report to the coordinator with the function zcl_SendReportCmd(). One of the parameters enables the use of...
View Article66AK2L06: Trouble Halting CPU error -1321
Part Number:66AK2L06I have a custom board designed around the 66AK2L06.I'm using CCS v7 with an XDS100v3.Power-up/Clocking/Reset sequence appears to be OK since I have RESET STATUS going high and a...
View ArticleTPS54140A: TPS54140A in 12V Batt Charger - light load start-up issue at low...
Part Number:TPS54140ADear Forum,My assigned customer has found some early field failures at minimum input voltage (10.8V), due to the device not starting up properly with their 60mA minimum load. As...
View Article