F28069 SCI max baud rate
Hi,I didn't find the maximum baud rate of the SCI of F28069 in its technical manual.I tried the example sci_echoback with different baud rates. I wrote a simple windows forms application to see the...
View ArticleClik here to view.
error: perspective switch job in ccs v5.1.0.9
Hi,a few days CCS v5.1.0.09 began to show an error when I try to launch debug session:and I cannot get the debug session menu appears, i.e., run, stop, pause, etc.I am using lcdk6748 with xds100v2.If...
View ArticleTest P2IN Push Button -- fails
I moved code that was working fine from one MSP processor to another. The code tests 2 ports to see if they are high or low to see if push buttons are pressed (hold low)?The ports I am using are for...
View ArticleINA214 Bipolar operation
I am thinking about using the INA214 to measure a 50mAp-p AC current. Would I be able to Power the INA214 with + and – 5VDC. I need the Amplified Output voltage to have zero DC offset.Would you...
View ArticleCC3000 Port and "__bic_SR_register"
Hi,I'm trying to port the Basic WiFi to a PIC24 micro and I'm not familiar with the MSP430 architecture and the operation of interrupts.Could someone please explain what the...
View ArticleSCI-B serial communication
Hello everyone,I am trying to use serial communication port: USB emulation/RS 232 SCI-B. I change the example code "echoback" from SCI-A to SCI-B. But I find Hyperterminal can not read or send...
View ArticleTPA3118D2 1Hz error cycling
I am building the schematic shown in the datasheet for the tpa3118d2 http://www.ti.com/lit/ds/symlink/tpa3118d2.pdf of the 2.1 sound system, and everything is working on board except the IC for the...
View ArticleWhich freq band is open in Brazil? thanks
I want to check CC1120 can be used in Brazil, in other word, which Frequency Bands is open in Brazil. Thanks very much.
View Article32-bit Floating to 32-bit Integer conversion on DSP C674x
Hi,Can anybody please tell me how to do a 32-bit Floating to 32-bit Integer conversion using an intrinsic or any other optimized way? But the requirement is the o/p should match the o/p of -...
View ArticleCC1120 - RF settings
Hello,I'm setting the CC1120 registers according to the recommendation I got from SmartRfStudio, yet when testing the transmission using my spectrum analyzer I keep getting my transmitted signal at...
View ArticleRe:Code execution from RAM and FLASH
Hi,Please help me in getting sample code for erasing and writing to flash.Also get me code to execute from RAM to erase and write to the flash area.Best Regards,Santosh.
View ArticleX-loader hang at reading boot sector
Hello all,I am developing a custom DM3730 based board and I have trouble with xloader. Output from uart is like thisTexas Instruments X-Loader 1.51 (Apr 26 2013 - 22:09:56)Starting X-loader on...
View ArticleUsing C2000 launchpad's xds100v2 emulator for another DSP
Can i use xds100 v2 emulator which is built in c2000 launchpad to program and emulate another C2000 DSP based board..?
View ArticleTI BLE Stack v1.3.1 released (April 18th 2013)
Download it at ti.com/ble-stackVersion 1.3.1April 18, 2013Notices:- This version of the Texas Instruments BLE stack and software is a minor update to the v1.3 release. It contains some minor bug fixes,...
View ArticleCCS
Hi All,I was downloading and installing the CCS software when I encountered an error message that told me to look in the Eclipse Configuration Log. Below is the content of the log. I uninstalled the...
View ArticleOOK with CC430
Hi, I have my own board with CC430F5137 working flawlessly at 433 MHz with 2-FSK and MSK at 250 kbps. However when I change to OOK at 250 kbps I am not able to receive anything on the other boards....
View ArticleTMS320C5515 EVM
Hello. I'm newbie in TMS320C5515 EVM. Wich transceivers can I use with TMS320C5515 EVM? And if I can where can I find some examples of programs with them?Kirill.
View ArticleInterfacing LM35 with MSP430 Launch pad
Hi, i was interfacing LM35 to MSP430 launch pad (MSP430g2452), and the LM35 is connected to analog channel A4 of launch pad, The code is mentioned below, I'm getting a constant output as 23 deg C, I...
View ArticleConfigure USB1 interrupt in Omap L-138
Hi all,I'm using OMAP L-138 and want to use USB1.1, I pick usb_dev_bulk to modify on it to match my application needs.In usb_dev_bulk.c:static void ConfigureDSPINTCIntUSB (void) { IntRegister(4,...
View ArticleBluetooth Low Energy Total Network Throughput
I understand that the stack is currently limited to 3 slaves connected to a master at a given time. I also understand the current throughput for a given connection to be limited to roughly...
View Article