WiLinik firmware in AM5728
Hi I'm newbie to WLAN bring up to am5728 custom board. Currently referring http://processors.wiki.ti.com/index.php/WL127x_Porting_Guide
View ArticleCapTIvate sheet questions
Team,We got some questions from sensor sheet vendor via customer.Attached the slide for their design.Would you please advise on these?(Please visit the site to view this file)[Qs] These questoins are...
View ArticleWork with/without debugger.
Hi!!I have a trouble.I have custom hardware based on SensorTag hardware. This hardware running under stack 2.1 perfect.Under stack 2.2 i have this issue: when devpack debugger is connected and target...
View ArticleUnable to find Power Mode API like MAC_PwrOffReq, MAC_PwrOnReq and...
Hi, I am currently working in TIMAC - Power Management module. Planning to use the battery management API to save the energy consumption. I hope the RF core is continuously ON in the TIMAC provided...
View ArticleHow to make LP board as standalone device without PC support?
Hi to all,I want flash my code to LP board.How to flash the code on LP board?i am having Mqtt_client.bin,Mqtt_client.out file which one is used to flash.In CCS uniflash i am Following below step i...
View ArticleClik here to view.
Datasheet of LME49723
Dear Sirs,I have a question about voltage noise density of LME49723.There is described as 3.6nV/√Hz in the the page 1 of datasheet of LME49723.Also,there is described as 3.2nV/√Hz to the page 3.I think...
View ArticleCC2640 Default Firmware
Hi,I have developed a custom device that uses CC2640 as the main processor. I'm going to order CC2640 but I am wondering what is the ble stack software version that comes with CC2640. Also, I want to...
View ArticleSYSBIOS exit when Ethernet cable connecte to K2EVM board with PDK example...
HiWhen i try to test PDK example delivered for K2E "NIMU_emacExample_EVMK2E_armBiosExampleProject" , The project results in SYSBIOS exit if Ethernet link is connected. Since this is a out of the box...
View ArticleDP83867IR RX_DV/RX_CTRL Strap pin MODE description
Hi,I have a question about DP83867IR Strap Pin "RX_DV/RX_CTRL".This "RX_DV/RX_CTRL" is strap pin for "Autoneg Disable" setting andwe can select MODE3 or MODE4.If I want to enable Auto Negotiaon, which...
View ArticleError in linked command file when compiling for TDA3XX platform
Hi,I am getting the following error when i am compiling my code for m4 core for TDA3xx platform.<Linking>"linker.cmd", line 250: error: program will not fit into available memory. placement with...
View Articlez-stack mesh - add a new input
Hi thereI defined SW_7 as below in hal_key.h :#define HAL_KEY_SW_7 0x40 // Button S2 if availablenow I have 2 questions1)what PORT and PIN are non-used in generic application or I can use for this...
View ArticlePCM1860 Pass band
Hello team,I would like to know about digital filter in PCM1860.Datasheet says Pass band is 0.454 Fs. However it is specified when 48ksps is used.My question is whether the pass band spec(0.454Fs) can...
View ArticleSN65HVD233 termination
Dear team,Using SN65HVD233 to connect at OBD port of Vehicle and measured a 60 ohm resistance between CANH and CANL of OBD port. Please confirm if We need to add terminating resistor on CAN line of...
View ArticleCC2630 is blocked by smart flash programmer.
Hello,I am using Smart Flash Programmer (SFP) Version 2 version 1.7.4 and a debuger XDS200 to download programming to CC2630 (design by myself).The Smart Flash Programmer can detect correctly the...
View ArticleClik here to view.
Drop out voltage of TPS70930DBVR @ the output of 3V
Hi,Details of drop out voltage for 3V regulator IC's are not given in the datasheet, Please provide the detailed information. Snap shot is attached for the reference.Regards,R.Subramaniasiva
View Articlec2000 piccolo
Hello all,I am using LAUNCHXL-F28027 and i need to know how to connect function generator with my launch pad and see the signal in the CROPlz help me i am new with this kit
View ArticleCCS Simulation support in future
Our customer wants to use the optimization tools using simulator such as...
View ArticleDoes TDA2x DSS support BT.656 with external syncs?
Hi Champions,My customer wants to implement the BT.656 output with external syncs which is similar as the BT.601, according the TRM the DSS BT-656 can't support the BT.601 with studio encoding...
View ArticleWhat Can I do with AM335X ICE V2 for Linux Development?
HiI installed AM335x Linux SDK on a host machine and created an SD card using cretae_sdcard.sh. The AM335x ICE V2 can boot from the SD card. I can login into it using root. From TI related documents,...
View Article