DS90UB940-Q1: The received error data
Part Number: DS90UB940-Q1Hi,I'm using DS90UB940-Q1 for automotive camera product. The Serializer is DS90UB925Q-Q1. Sometimes the DS90UB940-Q1 will receive error data. My questions is: In what...
View ArticleClik here to view.
WL18XX-BT-SP: WL1837MOD reporet Hardware ERROR event, code=0x6
Part Number: WL18XX-BT-SPHi ,Our customer reported that there was a probability error in playing bluetooth music and downloading the phone book.Bluetooth protocal stack log display HCI RX: Hardware...
View ArticleClik here to view.
ADS1256: Question Consultation
Part Number: ADS1256Hi,we have an 8-channel ADS acquisition chip ADS1256.Eight channels are all used as single-ended input.As described on page 14 of the data sheet, the AINCOM foot is not grounded for...
View ArticleINSTASPIN-BLDC: Instaspin Rs Recalculation error
Part Number: INSTASPIN-BLDCHello,I'm trying to run 2 BLDC motors using the lab6e example. I need to recalculate the Rs before every start and I enable this in the code with this line:...
View ArticleAM4372: Factory programming eMMC with AM4372 BootROM
Part Number: AM4372Hello,What is the recommended way to manufacture AM4372 based product with eMMC storage?I am specifically looking for suggestions or materials to program eMMC (in circuit) using boot...
View ArticleCCS / TIDA-010021： TIDA-010021
Part Number: TIDA-010021Tool/software: Code Composer StudioDear team,How does your TIDA-010021 package burn programs?What kind of burner should I use when using Uniflash?Best regards,Li
View ArticleDRV10987: Device can't start motor
Part Number: DRV10987Hi,I am having a lot of trouble trying to get this chip to spin atall. It vibrates slightly, and on my scope I can see the DRV applying a signal to all 3 motor phases, but it...
View ArticleTDA2P-ACD: Linux - VSDK IPC and Message Que
Part Number: TDA2P-ACDHi all,I have some usecase with different links. Some of them are running on RTOS (IPU2, DPS, EVE) and some of them on Linux (A15). So, after few hours, Linux just hangs, terminal...
View ArticleCC1352R: Porting SDK 2.40 to 3.10
Part Number: CC1352RHi,So far I've been successfully using the BLE 2.40 SDK. However, from anaylysis in different e2e thread it seems that TRNG driver used there takes too much current for my...
View ArticleLM2623: Correct C3 for duty cycle of 86%
Part Number: LM2623Dear experts,I want to boost from Vin (2.5V to 1.7V) to Vout(10V) with LM2623A. The output doesn't need to be perfectly stable (so it may exhibit ripple). Iout should be as much as...
View ArticleClik here to view.
UC3845: Current sens resistor calculation when extra fading voltage from Vref...
Part Number: UC3845Hi;I am making Constant voltage 5VDC flyback based power supply using UC3845. I have read TI datasheet . As per page number-25 Current sensing network design Equation number :...
View ArticleCC2530: How to create an end-device with arbitrary application (for example...
Part Number: CC2530HI friends,I want to create a Zigbee end-device. I want to use z-stack Home Automation v1.2 and cc2530 module. is there any documentation to how create an end device with arbitrary...
View ArticleClik here to view.
TPS543C20: TPS543C20 Sequence-EN and PGD
Part Number: TPS543C20This is my test of power-off sequence on TPS543C20EVMs. 1 channel is EN of Module-A, 2 channel is PGD of Module-A, 3 channel is EN of Module-B, 4 channel is PGD of Module-B. When...
View ArticleAWR1642BOOST: frame rate
Part Number: AWR1642BOOSTwhen I enable streaming of all data (range and Doppler heat-maps) the data UART can't seem to handle higher frame rates and I'm forced to reduce the frame rate to 1 or 2 FPS...
View ArticleMSP430FR5969: Regaring RST pin in MSP430FR5969
Part Number: MSP430FR5969Hi Team,I have one doubt in RST pin in MSP430fr5969. I am sending LPM4.5 to active mode when giving interrupt to RST Pin by using RESET_VECTOR but it is not going to Active...
View ArticleCCS: CPU TIMER0 for sine generation and TIMER1 for Adc triggering
Tool/software: Code Composer StudioHello,I am I am generating sine wave of 1000 points because my switching frequency is 50KHz and fundamental frequency is 50Hz so 50KHz/50Hz=1000, so I use CPU TIMER0...
View ArticleWEBENCH® Tools: Battery Managemnet System
Tool/software: WEBENCH® Design ToolsHi,As per the application we want to have a battery management system for our devices. The battery input will not more than 36v, 10Amp.In application, we want when...
View ArticleMSP432E401Y: MSP432E401Y
Part Number: MSP432E401YHi,i am using MSP432EA01Y LAUNCHPAD with cc2650moda (BLE). When i connect MSP432EA01Y LAUNCHPAD using usb cable with my laptop i should get 3.3V or 5V from the pins which...
View ArticleCCS/TMS320F2812: Device is locked or not connected. Operation cancelled.
Part Number: TMS320F2812Tool/software: Code Composer Studiodear friends,while dumping the code i got a problem as follows...C28xx: Flash Programmer: Device is locked or not connected. Operation...
View ArticleCCS/LAUNCHXL-F280049C: C28x EPWM Driver is not writing to registers
Part Number: LAUNCHXL-F280049CTool/software: Code Composer StudioHello,I have a problem using functions in epwm.h (part of c2000ware driverlib).I am not able to change any register value using epwm...
View Article