Clik here to view.
CCS/BQ40Z60: How to configure 'SOC Flag Config A'?
Part Number:BQ40Z60Tool/software: Code Composer Studio As I saw 'SOC Flag Config A' description of manual reference document, I notice there are different basis to set or clear TC, TD, FC and FD...
View ArticleIWR6843ISK-ODS: Verification of Rx Gain
Part Number:IWR6843ISK-ODSHi~I'd like to test the Rx Channel Gain of IWR6843_ODS Evk in order to evaluate module's quality.The Rx ch. gain can be estimated based on the loop gain of Tx and Rx path when...
View ArticleADCS7476: ADCS7476 data run error
Part Number:ADCS7476Dear Experts,there have a question：“why when they open the buffer memory the data is from BIT0--BIT11，and close the buffer memory the data is from BIT1--BIT12？”hope you can give...
View ArticleTINA/Spice: Time control switch in TINA-TI doesn't work correctly. Could you...
Tool/software:TINA-TI or Spice Models Hello guys, One of my customers is found some overshoot at TI IC output terminal when they plugged other IC input into the IC output.through a mechanical plug like...
View ArticleTMS320F28379D: Configuring CCPS and UPPS of QEP to fit different motor speed
Part Number:TMS320F28379DHi team, My customer is testing F2837x QEP and they would like to re-config CCPS and UPPS to get a better performance and low/high speed range.I noticed in our TRM:
View ArticleTLV8802: Asking for the recommendation to small package TLV8802
Part Number:TLV8802Hi Team,Customer is looking solution with small package TLV8802 dual OP. Would you please recommend the proper solution for this? BR,SHH
View ArticleCC1350: How define 1 Pin External interrupt for both rising and falling edge...
Part Number:CC1350Hello, I am working on a project where i want to use rising edge and falling edge for interrupts at the same pin,when rising edge is configured then Timer should start then i want to...
View ArticleCC3235SF: Radiotool CC3XXXRADIOTEST 1.0.3.10 does not have STOP transmission...
Part Number:CC3235SFHi *,I would like to know if there is a CLI command to stop the continunous transmission by thje device. I see only TX command with Time out.Our pupose is to do automated testing,...
View ArticleLM73606: Questions
Part Number:LM73606(1) Are the NC pins on the LM73606 internally connected to GND? This question comes from thermal design consideration.(2) What is the acceptable range of the 2.2uF on the VCC?...
View ArticleClik here to view.
TMUX1108: TMUX1108
Part Number:TMUX1108Hi TI,What do you mean by TMUX1108 CSON/CSOFF?Where is the capacitance value tested?thank you
View ArticleWEBENCH® Tools/EK-TM4C123GXL: how can i measure battery level in my tm4c123gh6pm
Part Number:EK-TM4C123GXLTool/software: WEBENCH® Design ToolsDear Experts,now i am working with tm4c123gh6pm based EK-TM4C123GXL evaluation kit, and i was powered up with 4*1,2V AAA battery, then i...
View ArticleLinux/TDA2SX: TDA2
Part Number:TDA2SXTool/software: LinuxDear TI officer: I have a TDA2x development board and an OPT8241-CDK-EVM.Can I put the OPT8241-CDK-EVM 's SDK: Voxel SDK on the TDA2 development board compiler...
View ArticleTCA9548A-Q1: for Ethernet Phys
Part Number:TCA9548A-Q1Hi,is it possible to use this switch (TCA9548A-Q1) to distribute/switch MDC/MDIO (system management interface) signals for Ethernet Phys? In the datasheet it says that it...
View ArticleTPS53647: TPS53647
Part Number:TPS53647hicould you explain how could we set the output voltageof TPS53647 to 0.82v by resistors e.g. without PMBUS?thanks
View ArticleClik here to view.
Linux/AM3358: DCAN errors on start
Part Number:AM3358Tool/software: LinuxHi,we're investigating issue on can where after boot when we set:/sbin/ip link set can0 type can bitrate 500000; /sbin/ip link set can0 up and have receptionwe see...
View ArticleCCS/CC1310: RF Core command
Part Number:CC1310Tool/software: Code Composer StudioHello.Correctly, I understand that all commands from #include <ti/drivers/rf/RF.h> are intended for use with TI-RTOS and NoRTOS mode ?And they...
View ArticleAWR1642: AWR1642 startup problem
Part Number:AWR1642From the official website data, the AWR1642 has two startup modes: 1, 001 (corresponding to sop2, sop1, sop0) normal startup mode; 2, 101 (corresponding to sop2, sop1, sop0) program...
View ArticleClik here to view.
TMS570LS3137: chip select using GPIO
Part Number:TMS570LS3137Hi Sir,I enabled spi2 driver in HALCOGEN and in spi2port, i have selected SCS[1] pin mode as GIO, as shown below:i have connected SPI2- CS1 pin to picoscope on the micro...
View ArticleFET of TPS82130
We have a question about TPS82130.Does this IC have short mode when FET is broken?We are concerned that Input voltage is output to load by FET broken.Best regards,Takahiro Nishizawa
View ArticleClik here to view.
DP83867CR: For SGMII input interface which connected to RJ45 for 100Base-TX
Part Number:DP83867CRHi Sir,I'm looking for a solution which support SGMII input interface which connected to RJ45 for 100Base-TX.I have found a similar product DP83867, please help confirm which it...
View Article