Need to add mt9t112 sensor as part of kernel
Hi,I have VirtualBox on Windows 7 with Ubuntu 12.04. Downloaded ti-sdk-beagle-05.05.01.00-Linux-x86-Install and installed and build uImageby following Dave's instructions. 1.export <SDK...
View ArticleClik here to view.
BQ24160RGEEVM-742 USB charging issue
Dear Sir,I worked with BQ24160EVM and the setting profile just like the screen-shut below.The battery connected is 3.7V(2210mAh) and almost approaching charging done (4.17V measured).However, the...
View Articlecannot open .out file
I am new to CCS, and I tried to write a simple hello world #include <stdio.h>void main(void) { printf("Hello World!\n");}but when I start debugging it , an error appears. It said "Encountered a...
View ArticleCDCE937 Questions
Hello,Please answer following questions about CDCE937.Q1: Data Retention of EEPROMData-sheet specify Data Retention is 10 years minimum.Customer needs Data Retention time more than 10 years.Please...
View ArticleUCC28070 current loop gain and phase measurement
Hi,I am trying to measuure UCC28070(interleaving CCM PFC) current loop gain and phase, there is two phase in the circuit, does that mean that I have to diable one phase's output and set the load at...
View ArticleKeystone II: can't boot kernel with device tree error
Hi,We just received XTCIEVMK2X Evaluation Module, I used the images from mcsdk_linux_3_00_00_08,however kernel can't boot successfully, pls see belows.TCI6638 EVM # tftpboot 0x87000000...
View ArticleSending private messages
Very basic question, but, how do I send private messages to other users?
View ArticleClik here to view.
Not getting acknowledgement on I2C2 of DM814x processor
Hi,We are using DM8148 ( Part Number: TMS320DM8148BCYE0 ) in one of our project.We have connected temperature sensor ( Part Number: TCN75AVUA ) with DM8148 through I2C-2, which was configured with...
View ArticleTLK100 "unmanaged"?
Question from a customer on the TLK100- is it possible to run the PHY “unmanaged” (i.e. not utilize the SMI interface and run in some sort of default mode?)
View ArticleAdding support for MSP430G2955 to the Launchpad 1.5?
Is there a way to reflash the emulator on the launchpad 1.5 so it can support the g2955? I can only get it to see up to a 2744.
View ArticleQuestion on INA219 calibration register and current LSB
Hi,I am using TI INA219 test board connecting to a DC power supply. Power supply plus --> Vin+. My shunt resistor is 0.025 ohm between Vin+ and Vin-. Vin- -->.10 ohm resistor --> power supply...
View ArticleThe VPss is locked up when "Overlow" detected。how can it be avoided？
I`m using a DM8168 board with DVR_RDK3.0 and encounter a big problem： VPSSM3 sometimes gets locked up When I disconnect or reconnect the video input cable. The debug message is as follows:...
View ArticleNDK application to fit in Internal RAM?
We are developing an Industrial Automation protocol Ethernet/IP on AM335x, which uses NDK. We had developed this previously using Lwip stack, and it could be executed DDRless(not tested, but the memory...
View ArticleAdding ECC data
Hello,I am new to use Code composer studio 5.3.Please can some body explain how to append ECC data using tool (ECC 470.exe or any tool ) in Code composer Studio 5.3 directly while Building project....
View ArticleC6678 - Accessing Multiple End Points when in PCIE Root Complex Mode
Hello,It appears that Pcie_writeRegs() can be used to configure an end point's register base.However, what happens when there is more than one peripheral? Is there any way to enumerate the bus when in...
View ArticleClik here to view.
BQ77910A：I cannot charge
I use BQ77910 as below。the BAT Voltage=22.07V（6S Polymer Lithium-Ion Battery）,After I insert a charge(CC=1.8A)，there is no charge current。I messure those pins：reference VSSPin CHG=11.8VPin DSG=0.9VCan...
View ArticleNeed IBIS-AMI model for C6678
Hi AllI need IBIS-AMI model for TMS320C6678 processor for post layout SERDES simulation for a new projectPlease HelpThanks
View ArticleProblem in dda_mmcsdBios.c
Hi,I am using OMAP-L138 EVM along with UI board to sample signals using A/D converter and my intention is to write sampled data to SD card having file system. I have working RTFS based MMCSD code to...
View ArticleBeagleBone & StarterWare: I can't get the examples to link. How does one...
Hello,I have two issues;1) I cannot get the blinky example to link correctly. In fact it was a challenge to get the project to build at all. I read on a forum that you needed to link the libraries in....
View ArticleClik here to view.
Photodiode
Hello,Could anyone please explain what is the purpose of T1? what it does? How does it do it? Wouldn't it make Vout to oscillate or Photo diode? I guess i don't understand properly the role of U2 and...
View Article