Part Number:AMC1210MB-EVM
Dear Support Team,
I have order AMC1210MB-EVM for a motor control project, but the related SW is not available on the web. Could you please help to get the Installation SW for the GUI?
And if possible, my customer would like to get the source code running on the Stellaris side of the EVM.
Best Regards,
Caglar
Part Number:AM1806
Dear Champs,
Is it possible to reset I2C0 only in AM1806?
My customer faced I2C communication fail and would like to reset I2C0 port of AM1806 only to minimize impact on all system.
But, when they set IRS bit of ICMDR register, the I2C communication was not recovered and they are doubting if I2C0 was not reset properly.
Could you please let me know how they can reset I2C0 only in AM1806?
their AM1806 is non-OS platform.
Thanks and Best Regards,
SI.
Part Number:TMDSICE3359
Hello,
I successfully launched EtherCAT master project with Acontis master stack on tmdsice3359. I used that document from TI: 
My simple network is TMDSICE3359<-> LaunchXL-F28379D. And it's working. Here is log from putty:
TI Industrial SDK Version - IASDK 1.1.0.8 Device name : AM3359 Chip Revision : AM335x ES1.2 [PG2.1] SYS/BIOS EcMaster Sample application running on ICE V2 Full command line: -auxclk 2000 -v 2 -t 100000 -perf -cpsw 1 1 1 m custom am33XX 1 1 0 001151 : Run demo now with cycle time 2000 usec 001151 : Using AuxClock 001151 : ========================== 001151 : Initialize EtherCAT Master 001151 : ========================== 001151 : EC-Master V2.9.0.06 (Protected) for SYSBIOS Copyright acontis technologies GmbH @ 2016 001152 : CPSW INF: Port 1, Prio 1, Flags [Polling] [Master], Phy 1, PhyInterface 32, MAC 38:d2:69:5f:69:49 001153 : CPSW INF: CPSW3G found. CPSW INF: HW-Id: 0x0019, RTL: 0, Major: 1, Minor: 0xc 001154 : CPSW INF: PHY found. Id=0x2000a211 001154 : CPSW INF: Restart PHY auto negotiation 002814 : CPSW INF: PHY auto negotiation completed 002832 : Unlicensed version, stop sending ethernet frames after 60 minutes! 002908 : Bus scan successful - 1 slaves found 002947 : 1 identical messages skipped 002947 : ****************************************************************************** 002947 : Slave ID............: 0x00000000 002947 : Bus Index...........: 0 002947 : Bus AutoInc Address.: 0x0000 002947 : Bus Station Address.: 0x03e9 (1001) 002947 : Bus Alias Address...: 0x0000 ( 0) 002947 : Vendor ID...........: 0x000A4D7A = ---- 002947 : Product Code........: 0x10001101 = Unknown 002947 : Revision............: 0x00000001 Serial Number: 0 002947 : ESC Type............: Beckhoff ET1100 (0x11) Revision: 0 Build: 3 002947 : Connection at Port A: yes (to 0x00010000) 002947 : Connection at Port D: no (to 0xFFFFFFFF) 002947 : Connection at Port B: no (to 0xFFFFFFFF) 002947 : Connection at Port C: no (to 0xFFFFFFFF) 002947 : Line Crossed........: no 002947 : Cfg Station Address.: 0x03e9 (1001) 002947 : PD IN Byte.Bit offset: 0.0 Size: 88 bits 002947 : PD OUT Byte.Bit offset: 0.0 Size: 88 bits 003066 : EtherCAT network adapter MAC: 38-D2-69-5F-69-49 003066 : ===================== 003066 : Start EtherCAT Master 003066 : ===================== 003073 : Master state changed from <UNKNOWN> to <INIT> 003218 : Master state changed from <INIT> to <PREOP> 003242 : Master state changed from <PREOP> to <SAFEOP> 003258 : Master state changed from <SAFEOP> to <OP> 003263 : 003263 : Job times during startup <INIT> to <OP>: 003263 : ================================================================ 003263 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 13.0/ 39.9 003263 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 6.0/ 14.8 003263 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 7.1/ 72.0 003263 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 3.6/ 27.7 003263 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1657.2/2009.1 003263 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.7/ 4.3 003263 : 005267 : ================================================================ 005267 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 19.2 005267 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.2 005267 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 5.9/ 11.1 005267 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 6.4 005267 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.2 005267 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 1.3 007269 : ================================================================ 007269 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 007269 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.2 007269 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 11.1 007269 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.0 007269 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.2 007269 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 1.3 009271 : ================================================================ 009271 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 009271 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.5 009271 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 11.1 009271 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.0 009271 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.8 009271 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 1.3 011273 : ================================================================ 011273 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 011273 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.5 011273 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 11.3 011273 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.0 011273 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.8 011273 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 013275 : ================================================================ 013275 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 013275 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.5 013275 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 5.9/ 11.8 013275 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.0 013275 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.8 013275 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 015277 : ================================================================ 015277 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 015277 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.7 015277 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 11.8 015277 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.0 015277 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 015277 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 017279 : ================================================================ 017279 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 017279 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.7 017279 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 11.8 017279 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.0 017279 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 017279 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 019281 : ================================================================ 019281 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 019281 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.7 019281 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 019281 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.0 019281 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 019281 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 021283 : ================================================================ 021283 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.6/ 21.4 021283 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.7 021283 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 021283 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.0 021283 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 021283 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 023285 : ================================================================ 023285 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.6/ 21.4 023285 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.7 023285 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 023285 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 023285 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 023285 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 025287 : ================================================================ 025287 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 025287 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.7 025287 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 025287 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 025287 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 025287 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 027289 : ================================================================ 027289 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 027289 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.7 027289 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 027289 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 027289 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 027289 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 029291 : ================================================================ 029291 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 029291 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.7 029291 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 029291 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 029291 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 029291 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 031293 : ================================================================ 031293 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 031293 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.7 031293 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 031293 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 031293 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 031293 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 033295 : ================================================================ 033295 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 033295 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.7 033295 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 033295 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 033295 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 033295 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 035297 : ================================================================ 035297 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 035297 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.7 035297 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 035297 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 035297 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 035297 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 037299 : ================================================================ 037299 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.6/ 21.4 037299 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.7 037299 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 037299 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 037299 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 037299 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 039301 : ================================================================ 039301 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 039301 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.7 039301 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 039301 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 039301 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 039301 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 041303 : ================================================================ 041303 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 041303 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.7 041303 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 041303 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 041303 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 041303 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 043305 : ================================================================ 043305 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 043305 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.7 043305 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 043305 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 043305 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 043305 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 045307 : ================================================================ 045307 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 045307 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.7 045307 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 5.9/ 12.2 045307 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 045307 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2003.9 045307 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 047309 : ================================================================ 047309 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 047309 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.7 047309 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 047309 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 047309 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 047309 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 049311 : ================================================================ 049311 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 049311 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.7 049311 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 049311 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 049311 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 049311 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 051313 : ================================================================ 051313 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 051313 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.7 051313 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 051313 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 051313 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 051313 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 053315 : ================================================================ 053315 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 053315 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 14.7 053315 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 053315 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 053315 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 053315 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 055317 : ================================================================ 055317 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 055317 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 14.7 055317 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 5.9/ 12.2 055317 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 055317 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 055317 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 057319 : ================================================================ 057319 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 057319 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 15.1 057319 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 5.9/ 12.2 057319 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 057319 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 057319 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 059321 : ================================================================ 059321 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 059321 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 059321 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 059321 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 059321 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 059321 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 061323 : ================================================================ 061323 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 061323 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 15.1 061323 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 061323 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 061323 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 061323 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 063325 : ================================================================ 063325 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 063325 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 063325 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 063325 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.2/ 7.3 063325 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 063325 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 065327 : ================================================================ 065327 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 065327 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 065327 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 065327 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.2/ 7.3 065327 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 065327 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 067329 : ================================================================ 067329 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.6/ 21.4 067329 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 067329 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 067329 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 067329 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 067329 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 069331 : ================================================================ 069331 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 069331 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 069331 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 069331 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 069331 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 069331 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 071333 : ================================================================ 071333 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 071333 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 15.1 071333 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 071333 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 071333 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 071333 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 073335 : ================================================================ 073335 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 073335 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 15.1 073335 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 073335 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 073335 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 073335 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 075337 : ================================================================ 075337 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.6/ 21.4 075337 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 15.1 075337 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 075337 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 075337 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 075337 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 077339 : ================================================================ 077339 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 077339 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 077339 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 077339 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 077339 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 077339 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 079341 : ================================================================ 079341 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 079341 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 15.1 079341 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 079341 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 079341 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 079341 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 081343 : ================================================================ 081343 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.6/ 21.4 081343 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 15.1 081343 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 081343 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 081343 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 081343 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 083345 : ================================================================ 083345 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.6/ 21.4 083345 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 083345 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 083345 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.2/ 7.3 083345 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 083345 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 085347 : ================================================================ 085347 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.6/ 21.4 085347 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 15.1 085347 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 085347 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.2/ 7.3 085347 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 085347 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 087349 : ================================================================ 087349 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 087349 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 15.1 087349 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 087349 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 087349 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 087349 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 089351 : ================================================================ 089351 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 089351 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 089351 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 089351 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 089351 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 089351 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 091353 : ================================================================ 091353 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 091353 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 091353 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 091353 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 091353 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 091353 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 093355 : ================================================================ 093355 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 093355 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 093355 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 093355 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 093355 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 093355 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 095357 : ================================================================ 095357 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 095357 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 095357 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 095357 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 095357 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 095357 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 097359 : ================================================================ 097359 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 097359 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 097359 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 097359 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 097359 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 097359 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 099361 : ================================================================ 099361 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 099361 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.1/ 15.1 099361 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 099361 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.3/ 7.3 099361 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 099361 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 101363 : ================================================================ 101363 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4 101363 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1 101363 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2 101363 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.2/ 7.3 101363 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0 101363 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7 103265 : 103265 : Job times before shutdown 103265 : ======================== 103265 : Shutdown EtherCAT Master 103265 : ======================== 103286 : Master state changed from <OP> to <INIT> 103553 : CPSW INF: Disable running RX-DMA 103553 : CPSW INF: RX+TX DMA disabled. Delay 500 103554 : EcMasterDemo stop.
We can see times in log:
101363 : ================================================================
101363 : PerfMsmt 'JOB_ProcessAllRxFrames' (avg/max) [usec]: 14.5/ 21.4
101363 : PerfMsmt 'JOB_SendAllCycFrames ' (avg/max) [usec]: 9.0/ 15.1
101363 : PerfMsmt 'JOB_MasterTimer ' (avg/max) [usec]: 6.0/ 12.2
101363 : PerfMsmt 'JOB_SendAcycFrames ' (avg/max) [usec]: 1.2/ 7.3
101363 : PerfMsmt 'Cycle Time ' (avg/max) [usec]: 1999.4/2004.0
101363 : PerfMsmt 'myAppWorkPd ' (avg/max) [usec]: 0.8/ 5.7
And here is my question - Cycle Time is quite long, it's about 2 msec. I would like to decrease it to e.g. 100us. What changes should I make to change cycle time?
I appreciate any help.
BR,
Dawid.
Part Number:AM3358
Tool/software: Linux
I'm using AM3358 with processor sdk 4.02.
I'm able to initialize tps65218 from u-boot after adding power_init_board function in board.c file.
I'm trying to initialize tps65218 in kernel .
While initializing tps65218 i'm getting error
[ 1.892345] tps65218 0-0024: Failed to request IRQ 0 for tps65218: -22
[ 1.899069] tps65218: probe of 0-0024 failed with error -22
Here is my dts node.
tps65218: tps65218@24 {
reg = <0x24>;
compatible = "ti,tps65218";
regulators {
dcdc1_reg: regulator@0 {
/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
regulator-name = "vdd_mpu";
compatible = "ti,tps65218-dcdc1";
regulator-min-microvolt = <912500>;
regulator-max-microvolt = <1351500>;
regulator-boot-on;
regulator-always-on;
};
dcdc2_reg: regulator@1 {
/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
regulator-name = "vdd_core";
compatible = "ti,tps65218-dcdc2";
regulator-min-microvolt = <912500>;
regulator-max-microvolt = <1150000>;
regulator-boot-on;
regulator-always-on;
};
dcdc3_reg: regulator@2 {
/* VDDS_DDR voltage limits 1.35V with +/-4% tolerance */
regulator-name = "vdds_ddr";
compatible = "ti,tps65218-dcdc3";
regulator-min-microvolt = <1283000>;
regulator-max-microvolt = <1418000>;
regulator-boot-on;
regulator-always-on;
};
dcdc4_reg: regulator@3 {
/* VDDS_SYSTEM_33 voltage 3.3v */
regulator-name = "vdd_3v3";
compatible = "ti,tps65218-dcdc4";
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
dcdc5_reg: regulator@4 {
regulator-always-on;
compatible = "ti,tps65218-dcdc5";
};
dcdc6_reg: regulator@5 {
regulator-always-on;
compatible = "ti,tps65218-dcdc6";
};
ldo1_reg: regulator@6 {
/* VDDS_SYSTEM_18 voltage 1.8v */
regulator-name = "vdd_1v8";
compatible = "ti,tps65218-ldo1";
regulator-always-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
};
};
Following device tree documentation it includes interrupt
How to define it?
Part Number:CC2530
Hello,
I have used the following reporting command to send Report to ZNP:
static void zclReport_Hue_Command (uint8 *device_hue_state)
{
afAddrType_t dstaddr;
dstaddr.addr.shortAddr = zclColor_DstAddr.addr.shortAddr;
dstaddr.addrMode = afAddr16Bit;
dstaddr.endPoint = zclColor_DstAddr.endPoint;
dstaddr.panId = zclColor_DstAddr.panId;
zclReportCmd_t rptcmd;
rptcmd.numAttr = 1;
rptcmd.attrList[0].attrID = ATTRID_LIGHTING_COLOR_CONTROL_CURRENT_HUE;
rptcmd.attrList[0].dataType = ZCL_DATATYPE_UINT8;
rptcmd.attrList[0].attrData = device_hue_state;
zcl_SendReportCmd(ENDPOINT, &dstaddr ,
ZCL_CLUSTER_ID_LIGHTING_COLOR_CONTROL, &rptcmd,
ZCL_FRAME_SERVER_CLIENT_DIR, 1, 0 );
}
I have used this one sending for Hue and the following one for sending Saturation
static void zclReport_Sat_Command (uint8 *device_sat_state)
{
afAddrType_t dstaddr;
dstaddr.addr.shortAddr = zclColor_DstAddr.addr.shortAddr;
dstaddr.addrMode = afAddr16Bit;
dstaddr.endPoint = zclColor_DstAddr.endPoint;
dstaddr.panId = zclColor_DstAddr.panId;
zclReportCmd_t rptcmd;
rptcmd.numAttr = 1;
rptcmd.attrList[0].attrID = ATTRID_LIGHTING_COLOR_CONTROL_CURRENT_SATURATION;
rptcmd.attrList[0].dataType = ZCL_DATATYPE_UINT8;
rptcmd.attrList[0].attrData = device_sat_state;
zcl_SendReportCmd(ENDPOINT, &dstaddr ,
ZCL_CLUSTER_ID_LIGHTING_COLOR_CONTROL, &rptcmd,
ZCL_FRAME_SERVER_CLIENT_DIR, 1, 0 );
}
Now here I can only send report on Hue, for Saturation I cant see any report being sent, what could be the problem here?
Part Number:AM3352
Hi,
Is it possible to modify the PRIORITYTHRESHOLD inside an interrupt routine?
Currently we have an interrupt with PRIORITYTHRESHOLD set as "0x30"
and due to some requirment we need to increase the THRESHOLD to 0x08 inside the
interrupt service routine and return it back to 0x30 later.
Unfortunately we are not able to achieve this, we are getting lower priority
interrupts(like 0x10,0x20) even though the THRESHOLD is set to 0x08.
Below is the procedure we are trying to implement.
1> Enable priority masking threshold(PRIORITYTHRESHOLD) for an interrupt as 0x30
as mentioned in the TRM's "INTC Preemptive Processing Sequence".
2> Once the interrupt routine is called, modify the PRIORITYTHRESHOLD value to 0x08
so that interrupts lower or equal priority than 0x08 are masked.
3> Return back the PRIORITYTHRESHOLD value to the original one (0x30).
Please let me if this kind of usage is possible and if there is any
suggestion to implement this.
OS used: This is a non-OS bare metal application.
Best Regards
paddu
Part Number:AMC1304L05
Hello,
according to the datasheet (revision 2017) the AMC1304L05 has a fail safe function. §8.4.1. Fail-Safe Output says: "In the case of a missing high-side supply voltage (LDOIN), ..." "Therefore, the AMC1304 implements a fail-safe output function". We use this function successfully together with logic in an FPGA. It will trigger an error if the ADCs datastream does not toggle within 128 clock cycles.
The AMC1304L05 is specified for LDOIN between 4 to 18VDC. We use it with 5V generated by an digital isolator (ADuM64xx).
In our application we trigger an error, if the primary power rail for the isolators drops below 4V. In case of VCCprimary < 4.5V the isolators try to generate 5V but this is not guaranteed. It might be anything between below 4V (due to losses) up to 5V.
The word "missing" in the AMC1304L05 datasheet is somehow unclear, however, as it implies that this error function is only active when LDOIN = 0V.
In FMEA and hasard rate discussions the following question was asked. What is the behavior of the ADCs error function in case of 0V < LDOIN <4V. We could not find any information about this point in the datasheet. Does the error handler raise an error (no toggling of data lines) or is it simply unspecified and it is up to the user to supervise the power supply for LDOIN?
Thank You very much in advance for clarification
Robert
Part Number:TMS320C6678
Hi,
I'm working on a customizd board with C6678 in ethernet bootloader mode. C6678 will send the BOOTP packets every 3 seconds before the *.eth packets sent.
But I found that when the network interface was negotiated as 100M bps, the BOOTP packet will not be sent (Using wireshark tool, I can't capture the BOOTP protocol packets). When the interface was configured 1000M bps, the BOOTP packet will be sent again.
I'm not very familiar with the RBL logic for the ethernet boot mode. Can I modify the RBL to send BOOTP packet when in 100M bps configuration ?
Thanks~
--
Regards Lin
Part Number:TMS570LC4357
Reopening of Unexpected Performance Monitoring Unit Data Cache Miss counter discussion.
Part Number:TLV320AIC3107
Will the Integrated Class D Amplifier give proper output at 3.3 V for SPVDD. I am Trying to integrate a 0.7W 8Ω Speaker with the codec. My application is voice Calling.
Part Number:CC2538
Hello,
When reading the datasheet and the User Manual, there are some mentions of SWO trace (Cortex-M3); however, I couldn't find any information on how to configure the pins to enable this feature. Is there a guide available somewhere? I know that you have some information on the info-centre of ARM: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.ddi0337e/index.html but it is more protocol configuration rather than pins configurations, which should be vendor-defined.
On https://e2e.ti.com/support/wireless_connectivity/zigbee_6lowpan_802-15-4_mac/f/158/p/573820/2235764?tisearch=e2e-sitesearch&keymatch=cc2538%20trace#2235764 , one manages to make it works using pin PB5 but that person did not share all information (I would like to use pin PB7 instead for example). Even with those settings, when I've tried it with a J-Link probe debugger; it failed.
HWREG(0x44010010) = 0x1; (????)
HWREG(0x400DA400) |= 0x20; (Set pin PB5 direction)
Does the CC2538 really support trace debugging?
Thank you in advance,
Steven
Part Number:CC2650
Tool/software: Code Composer Studio
hi,
I am facing a warning as-
Description Resource Path Location Type
This project contains 2 unresolved buildable linked resource(s). The project may not build as expected. GlucoseCollectorStack project Problem
please try to resolve.
Part Number:PROCESSOR-SDK-AM335X
Tool/software: Linux
I need somebody's Help.
My board can pick up the IP by DHCP under U-BOOT. But it can't get IP under the Linux.
1. My board is derived from AM335X EVMSK.
1.1 There is only one PHY.
1.2 phy-mode = "rmii";
2. My SDK is am437x-evm-linux-sdk-src-04.00.00.04
3. U-Boot
3.1 My PHY address in the file /board/ti/am335x/board.c
static struct cpsw_slave_data cpsw_slaves[] = {
{
.slave_reg_ofs = 0x208,
.sliver_reg_ofs = 0xd80,
.phy_addr = 1,
},
{
.slave_reg_ofs = 0x308,
.sliver_reg_ofs = 0xdc0,
.phy_addr = 0,
},
};
3.2 My ethnet(eth0) works well under U-BOOT.
04.02 SD!>mii info
PHY 0x01: OUI = 0x80017, Model = 0x09, Rev = 0x00, 100baseT, FDX
04.02 SD!>mii dump 1 1
1. (786d) -- PHY status register --
(8000:0000) 1.15 = 0 100BASE-T4 able
(4000:4000) 1.14 = 1 100BASE-X full duplex able
(2000:2000) 1.13 = 1 100BASE-X half duplex able
(1000:1000) 1.12 = 1 10 Mbps full duplex able
(0800:0800) 1.11 = 1 10 Mbps half duplex able
(0400:0000) 1.10 = 0 100BASE-T2 full duplex able
(0200:0000) 1. 9 = 0 100BASE-T2 half duplex able
(0100:0000) 1. 8 = 0 extended status
(0080:0000) 1. 7 = 0 (reserved)
(0040:0040) 1. 6 = 1 MF preamble suppression
(0020:0020) 1. 5 = 1 A/N complete
(0010:0000) 1. 4 = 0 remote fault
(0008:0008) 1. 3 = 1 A/N able
(0004:0004) 1. 2 = 1 link status
(0002:0000) 1. 1 = 0 jabber detect
(0001:0001) 1. 0 = 1 extended capabilities
3.3 Device tree for PHY
cpsw_default: cpsw_default {
pinctrl-single,pins = <
AM33XX_IOPAD(0x90C, PIN_INPUT_PULLDOWN | MUX_MODE1) /* GMII1_CRS.RMII1_CRS_DV ok */
AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE1) /* GMII1_RXERR/RMII1_RXERR ok */
AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rgmii1_tctl ok */
AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rgmii1_td1 ok*/
AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rgmii1_td0 ok*/
AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rgmii1_rd1 ok */
AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rgmii1_rd0 ok */
AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE0) /* RMII1_REFCLK ok */
>;
};
&mac {
slaves = <1>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&cpsw_default>;
pinctrl-1 = <&cpsw_sleep>;
status = "okay";
};
&davinci_mdio {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&davinci_mdio_default>;
pinctrl-1 = <&davinci_mdio_sleep>;
status = "okay";
};
&cpsw_emac0 {
phy_id = <&davinci_mdio>, <1>;
phy-mode = "rmii";
};
4. Under Linux
4.1 The Device tree
cpsw_default: cpsw_default {
pinctrl-single,pins = <
/* Slave 1 */
AM33XX_IOPAD(0x90C, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* GMII1_CRS.RMII1_CRS_DV ok */
AM33XX_IOPAD(0x910, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* GMII1_RXERR/RMII1_RXERR ok */
AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txen.rgmii1_tctl */
AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd1.rgmii1_td1 */
AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* mii1_txd0.rgmii1_td0 */
AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd1.rgmii1_rd1 */
AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE2) /* mii1_rxd0.rgmii1_rd0 */
AM33XX_IOPAD(0x944, PIN_INPUT_PULLDOWN | MUX_MODE0) /* RMII1_REFCLK ok */
>;
};
&mac {
slaves = <1>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&cpsw_default>;
pinctrl-1 = <&cpsw_sleep>;
status = "okay";
};
&davinci_mdio {
pinctrl-names = "default", "sleep";
pinctrl-0 = <&davinci_mdio_default>;
pinctrl-1 = <&davinci_mdio_sleep>;
status = "okay";
};
&cpsw_emac0 {
phy_id = <&davinci_mdio>, <1>;
phy-mode = "rmii";
};
&phy_sel {
rmii-clock-ext;
};
5. Linux Log
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.59-ga75d8e9305 (hpgw@ubuntu) (gcc version 6.2.1 20161016 (Linaro GCC 6.2-2016.11) ) #33 PREEMPT Thu Mar 15 16:00:30 CST 2018
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt:Machine model: TI AM335x EVM-SK
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 48 MiB at 0x8a800000
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] AM335X ES2.1 (neon)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyO0,115200n8 root=PARTUUID=000828c2-02 rw rootfstype=ext4 rootwait
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 198324K/262144K available (7168K kernel code, 274K rwdata, 2324K rodata, 1024K init, 274K bss, 14668K reserved, 49152K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0800000 (8160 kB)
[ 0.000000] .init : 0xc0b00000 - 0xc0c00000 (1024 kB)
[ 0.000000] .data : 0xc0c00000 - 0xc0c44810 ( 275 kB)
[ 0.000000] .bss : 0xc0c44810 - 0xc0c89044 ( 275 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[ 0.000000] OMAP clockevent source: timer2 at 24000000 Hz
[ 0.000031] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.000078] clocksource: timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000102] OMAP clocksource: timer1 at 24000000 Hz
[ 0.000550] clocksource_probe: no matching clocksources found
[ 0.000894] Console: colour dummy device 80x30
[ 0.000947] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
[ 0.000964] This ensures that you still see kernel messages. Please
[ 0.000977] update your kernel commandline.
[ 0.001021] Calibrating delay loop... 298.59 BogoMIPS (lpj=1492992)
[ 0.067594] pid_max: default: 32768 minimum: 301
[ 0.067897] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.067926] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.069638] CPU: Testing write buffer coherency: ok
[ 0.070313] Setting up static identity map for 0x80100000 - 0x80100060
[ 0.072265] EFI services will not be available.
[ 0.075620] devtmpfs: initialized
[ 0.110276] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 0.111040] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.111092] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.118394] pinctrl core: initialized pinctrl subsystem
[ 0.121050] NET: Registered protocol family 16
[ 0.125666] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.161403] omap_hwmod: debugss: _wait_target_disable failed
[ 0.247677] cpuidle: using governor ladder
[ 0.277661] cpuidle: using governor menu
[ 0.293697] OMAP GPIO hardware version 0.1
[ 0.326817] omap-gpmc 50000000.gpmc: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/nandflash_pins_s0, deferring probe
[ 0.334501] No ATAGs?
[ 0.334542] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.399221] edma 49000000.edma: TI EDMA DMA engine driver
[ 0.408770] omap_i2c 44e0b000.i2c: could not find pctldev for node /ocp/l4_wkup@44c00000/scm@210000/pinmux@800/pinmux_i2c0_pins, deferring probe
[ 0.409130] media: Linux media interface: v0.10
[ 0.409282] Linux video capture interface: v2.00
[ 0.409405] pps_core: LinuxPPS API ver. 1 registered
[ 0.409426] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.409487] PTP clock support registered
[ 0.409587] EDAC MC: Ver: 3.0.0
[ 0.412113] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400
[ 0.412907] Advanced Linux Sound Architecture Driver Initialized.
[ 0.415534] clocksource: Switched to clocksource timer1
[ 0.442582] NET: Registered protocol family 2
[ 0.444264] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.444352] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.444429] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.444579] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.444628] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.444924] NET: Registered protocol family 1
[ 0.445947] RPC: Registered named UNIX socket transport module.
[ 0.445977] RPC: Registered udp transport module.
[ 0.445994] RPC: Registered tcp transport module.
[ 0.446011] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.447849] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available
[ 0.453287] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.474316] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.476897] NFS: Registering the id_resolver key type
[ 0.476974] Key type id_resolver registered
[ 0.476995] Key type id_legacy registered
[ 0.477103] ntfs: driver 2.1.32 [Flags: R/O].
[ 0.481542] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[ 0.481584] io scheduler noop registered
[ 0.481604] io scheduler deadline registered
[ 0.482019] io scheduler cfq registered (default)
[ 0.485429] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[ 0.651953] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[ 0.661227] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 158, base_baud = 3000000) is a 8250
[ 1.256174] console [ttyS0] enabled
[ 1.263537] omap_rng 48310000.rng: OMAP Random Number Generator ver. 20
[ 1.270602] [drm] Initialized
[ 1.278084] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 1.284761] [drm] No driver support for vblank timestamp query.
[ 1.330466] Console: switching to colour frame buffer device 60x34
[ 1.342126] tilcdc 4830e000.lcdc: fb0: frame buffer device
[ 1.409876] brd: module loaded
[ 1.429212] loop: module loaded
[ 1.438834] libphy: Fixed MDIO Bus: probed
[ 1.515607] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[ 1.521841] davinci_mdio 4a101000.mdio: detected phy mask fffffffd
[ 1.529373] libphy: 4a101000.mdio: probed
[ 1.533448] davinci_mdio 4a101000.mdio: phy[1]: device 4a101000.mdio:01, driver NS DP83848C 10/100 Mbps PHY
[ 1.544940] cpsw 4a100000.ethernet: Detected MACID = 88:33:14:fc:ca:18
[ 1.551953] cpsw 4a100000.ethernet: device node lookup for pps timer failed
[ 1.559310] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies)
[ 1.570558] mousedev: PS/2 mouse device common for all mice
[ 1.577228] i2c /dev entries driver
[ 1.584821] cpuidle: enable-method property 'ti,am3352' found operations
[ 1.594108] omap_hsmmc 48060000.mmc: Got CD GPIO
[ 1.603536] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.615169] NET: Registered protocol family 17
[ 1.620417] Key type dns_resolver registered
[ 1.625217] omap_voltage_late_init: Voltage driver support not added
[ 1.644394] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[ 1.649862] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
[ 1.659391] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xdc
[ 1.666101] nand: ESMT NAND 512MiB 3,3V 8-bit
[ 1.670506] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 1.678227] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[ 1.683893] 13 ofpart partitions found on MTD device omap2-nand.0
[ 1.690088] Creating 13 MTD partitions on "omap2-nand.0":
[ 1.695577] 0x000000000000-0x000000080000 : "NAND.SPL"
[ 1.704323] 0x000000080000-0x000000100000 : "NAND.SPL.backup1"
[ 1.713694] 0x000000100000-0x000000180000 : "NAND.SPL.backup2"
[ 1.722867] 0x000000180000-0x000000200000 : "NAND.SPL.backup3"
[ 1.731803] 0x000000200000-0x000000280000 : "NAND.u-boot-spl-os"
[ 1.740977] 0x000000280000-0x000000380000 : "NAND.u-boot"
[ 1.749855] 0x000000380000-0x000000400000 : "NAND.u-boot-env"
[ 1.758855] 0x000000400000-0x000000480000 : "NAND.u-boot-env.backup1"
[ 1.768612] 0x000000480000-0x000000a80000 : "NAND.kernel"
[ 1.779649] 0x000000a80000-0x000000b00000 : "NAND.climax.config"
[ 1.788997] 0x000000b00000-0x000000c00000 : "NAND.climax.tmp"
[ 1.798013] 0x000000c00000-0x000000f00000 : "NAND.climax.preserved"
[ 1.808525] 0x000000f00000-0x000020000000 : "NAND.rootfs"
[ 2.055931] tps65910 0-002d: No interrupt support, no core IRQ
[ 2.065364] random: fast init done
[ 2.069333] vrtc: supplied by vbat
[ 2.077449] vio: supplied by vbat
[ 2.083096] vdd1: supplied by vbat
[ 2.089456] vdd2: supplied by vbat
[ 2.097915] vdig1: supplied by vbat
[ 2.103671] vdig2: supplied by vbat
[ 2.109577] vpll: supplied by vbat
[ 2.115237] vdac: supplied by vbat
[ 2.120876] vaux1: supplied by vbat
[ 2.126857] vaux2: supplied by vbat
[ 2.132602] vaux33: supplied by vbat
[ 2.138518] vmmc: supplied by vbat
[ 2.144286] vbb: supplied by vbat
[ 2.150518] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz
[ 2.157931] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 600000 KHz
[ 2.165355] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 600000000 (-34)
[ 2.175020] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 300000 KHz
[ 2.187052] omap_hsmmc 48060000.mmc: Got CD GPIO
[ 2.252734] input: gpio_buttons0 as /devices/platform/gpio_buttons0/input/input0
[ 2.266157] hctosys: unable to open rtc device (rtc0)
[ 2.273800] ALSA device list:
[ 2.277102] No soundcards found.
[ 2.286387] Waiting for root device PARTUUID=000828c2-02...
[ 2.386243] mmc0: host does not support reading read-only switch, assuming write-enable
[ 2.398656] mmc0: new high speed SDHC card at address aaaa
[ 2.407991] mmcblk0: mmc0:aaaa SU04G 3.69 GiB
[ 2.417131] mmcblk0: p1 p2
[ 2.557359] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 2.566076] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 2.584766] devtmpfs: mounted
[ 2.595992] Freeing unused kernel memory: 1024K
[ 3.044022] systemd[1]: System time before build time, advancing clock.
[ 3.237228] systemd[1]: systemd 230 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN)
[ 3.258242] systemd[1]: Detected architecture arm.
Welcome to Arago 2017.10!
[ 3.308773] systemd[1]: Set hostname to <am335x-evm>.
[ 4.141637] systemd[1]: [/lib/systemd/system/gadget-init.service:15] Unknown lvalue 'ExecStopPre' in section 'Service'
[ 5.079697] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 5.116930] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 5.157424] systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
[ 5.197476] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 5.238002] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ 5.277379] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Created slice User and Session Slice.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ OK ] Reached target Paths.
[ OK ] Reached target Swap.
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Listening on Process Core Dump Socket.
[ OK ] Created slice System Slice.
[ OK ] Reached target Slices.
Starting alignment.service...
Starting Journal Service...
Starting Load Kernel Modules...
[ OK ] Created slice system-getty.slice.
Starting Remount Root and Kernel File Systems...
Starting Create Static Device Nodes in /dev...
[ 6.143807] cryptodev: loading out-of-tree module taints kernel.
[ 6.187193] cryptodev: disagrees about version of symbol crypto_alloc_ahash
[ 6.194304] cryptodev: Unknown symbol crypto_alloc_ahash (err -22)
Mounting Debug File System...
[ 6.284298] cryptodev: disagrees about version of symbol crypto_ahash_setkey
[ 6.386199] cryptodev: Unknown symbol crypto_ahash_setkey (err -22)
[ 6.441654] cryptodev: disagrees about version of symbol crypto_alloc_aead
[ 6.441700] cryptodev: Unknown symbol crypto_alloc_aead (err -22)
[ 6.441744] cryptodev: disagrees about version of symbol crypto_aead_setauthsize
[ 6.441765] cryptodev: Unknown symbol crypto_aead_setauthsize (err -22)
[ 6.441899] cryptodev: disagrees about version of symbol crypto_destroy_tfm
[ 6.441919] cryptodev: Unknown symbol crypto_destroy_tfm (err -22)
[ 6.442044] cryptodev: disagrees about version of symbol crypto_aead_setkey
[ 6.442063] cryptodev: Unknown symbol crypto_aead_setkey (err -22)
[ 6.442347] cryptodev: disagrees about version of symbol crypto_ahash_final
[ 6.442366] cryptodev: Unknown symbol crypto_ahash_final (err -22)
[ 6.442757] cryptodev: disagrees about version of symbol crypto_alloc_skcipher
[ 6.442777] cryptodev: Unknown symbol crypto_alloc_skcipher (err -22)
[ 6.512141] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 6.637934] uio_module_drv: disagrees about version of symbol _dev_info
[ 6.637977] uio_module_drv: Unknown symbol _dev_info (err -22)
[ 6.638117] uio_module_drv: disagrees about version of symbol dev_err
[ 6.638137] uio_module_drv: Unknown symbol dev_err (err -22)
[ 6.646558] uio_module_drv: disagrees about version of symbol kobject_uevent
[ 6.646595] uio_module_drv: Unknown symbol kobject_uevent (err -22)
Starting Setup Virtual Console...
Mounting POSIX Message Queue File System...
Mounting Temporary Directory...
[ OK ] Listening on udev Kernel Socket.
[ OK ] Listening on Network Service Netlink Socket.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Debug File System.
[ OK ] Mounted Temporary Directory.
[ OK ] Started alignment.service.
[FAILED] Failed to start Load Kernel Modules.
See 'systemctl status systemd-modules-load.service' for details.
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Started Create Static Device Nodes in /dev.
[ OK ] Started Setup Virtual Console.
[ OK ] Started Journal Service.
Starting udev Kernel Device Manager...
Starting udev Coldplug all Devices...
[ OK ] Reached target Local File Systems (Pre).
Mounting /var/volatile...
Mounting /media/ram...
Starting Flush Journal to Persistent Storage...
Mounting Configuration File System...
Starting Apply Kernel Variables...
[ OK ] Mounted Configuration File System.
[ OK ] Mounted /var/volatile.
[ OK ] Mounted /media/ram.
[ OK ] Started Apply Kernel Variables.
[ 9.634276] systemd-journald[96]: Received request to flush runtime journal from PID 1
Starting Load/Save Random Seed...
[ OK ] Reached target Local File Systems.
[ OK ] Started udev Kernel Device Manager.
[ OK ] Started Flush Journal to Persistent Storage.
[ OK ] Started Load/Save Random Seed.
Starting Create Volatile Files and Directories...
[ OK ] Started Create Volatile Files and Directories.
Starting Network Time Synchronization...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Network Time Synchronization.
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Time Synchronized.
[ OK ] Found device /dev/ttyS0.
[ 17.870709] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 18.572490] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[ OK ] Started udev Coldplug all Devices.
[ OK ] Reached target System Initialization.
[ OK ] Listening on dropbear.socket.
[ OK ] Listening on RPCbind Server Activation Socket.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ OK ] Started D-Bus System Message Bus.
[ 22.364179] omap_hwmod: pruss: _wait_target_ready failed: -16
[ 22.502388] pruss-soc-bus 4a326000.pruss-soc-bus: use pm_runtime_put_sync_suspend() in driver?
[ 22.594629] pruss-soc-bus 4a326000.pruss-soc-bus: couldn't enable module
[ 22.685037] pruss-soc-bus: probe of 4a326000.pruss-soc-bus failed with error -16
[ 22.777393] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[ 22.901400] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[ 22.996055] omap-aes 53500000.aes: will run requests pump with realtime priority
[ 23.537584] pvrsrvkm: disagrees about version of symbol dev_err
[ 23.599366] pvrsrvkm: Unknown symbol dev_err (err -22)
[ 23.711254] wkup_m3_ipc 44e11324.wkup_m3_ipc: could not get rproc handle
[ 23.900167] PM: Cannot get wkup_m3_ipc handle
[ 24.279637] pvrsrvkm: disagrees about version of symbol dev_err
[ 24.371321] pvrsrvkm: Unknown symbol dev_err (err -22)
Starting Avahi mDNS/DNS-SD Stack...
[ OK ] Started System Logging Service.
[ OK ] Started Kernel Logging Service.
Starting Network Service...
Starting uim-sysfs.service...
Starting Login Service...
Starting Print notice about GPLv3 packages...
Starting Telephony service...
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Timers.
[ OK ] Started Network Service.
[ 29.970823] net eth0: initializing cpsw version 1.12 (0)
[ 30.116151] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4
[ 30.122640] cpsw 4a100000.ethernet: ALE Table size 1024
[ 30.417043] NS DP83848C 10/100 Mbps PHY 4a101000.mdio:01: attached PHY driver [NS DP83848C 10/100 Mbps PHY] (mii_bus:phy_addr=4a101000.mdio:01, irq=-1)
[ 30.656366] Bluetooth: Core ver 2.22
[ 30.731269] NET: Registered protocol family 31
[ 30.771100] cpts ptp bc clkid 0
[ 30.829236] Bluetooth: HCI device and connection manager initialized
[ 30.988229] Bluetooth: HCI socket layer initialized
[ 30.993268] Bluetooth: L2CAP socket layer initialized
[ 31.206455] Bluetooth: SCO socket layer initialized
[ 31.289746] remoteproc remoteproc0: wkup_m3 is available
[ 31.309408] PM: Cannot get wkup_m3_ipc handle
[ 31.309656] remoteproc remoteproc0: powering up wkup_m3
[ 31.456701] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 224268
[ 31.457383] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x192
[ 31.458639] remoteproc remoteproc0: remote processor wkup_m3 is now up
[ OK ] Started Avahi mDNS/DNS-SD Stack.
[ OK ] Started Telephony service.
[ OK ] Started Login Service.
[ 32.726749] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
[ OK ] Reached target Network.
Starting Simple Network Management Protocol (SNMP) Daemon....
Starting Lightning Fast Webserver With Light System Requirements...
[ OK ] Started strongSwan IPsec IKEv1/IKEv2 daemon using ipsec.conf.
Starting Permit User Sessions...
Starting Enable and configure wl18xx bluetooth stack...
Starting Network Name Resolution...
[ OK ] Started Lightning Fast Webserver With Light System Requirements.
[ OK ] Started Permit User Sessions.
[ 37.785928] random: crng init done
[ OK ] Started Network Name Resolution.
[ 39.188820] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ OK ] Found device /dev/ttyS3.
[ 42.822217] NET: Registered protocol family 15
[ OK ] Started Enable and configure wl18xx bluetooth stack.
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyS3.
[ 50.209275] Initializing XFRM netlink socket
[ OK ] Found device /dev/mmcblk0p1.
_____ _____ _ _
| _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_
| | _| .'| . | . | | __| _| . | | | -_| _| _|
|__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_|
|___| |___|
Arago Project http://arago-project.org am335x-evm ttyS0
Arago 2017.10 am335x-evm ttyS0
am335x-evm login: [ 56.132136] udc-core: couldn't find an available UDC - added [g_multi] to list of pending drivers
[ 62.484404] TI-am335x-tsc TI-am335x-tsc: ti,charge-delay not specified
[ 62.589222] input: ti-tsc as /devices/platform/ocp/44e0d000.tscadc/TI-am335x-tsc/input/input1
[ 62.729003] PM: bootloader does not support rtc-only!
[ 63.813828] 47401300.usb-phy supply vcc not found, using dummy regulator
[ 63.918298] 47401b00.usb-phy supply vcc not found, using dummy regulator
[ 64.357728] usbcore: registered new interface driver usbfs
[ 64.363711] usbcore: registered new interface driver hub
[ 64.547889] usbcore: registered new device driver usb
[ 65.268817] musb-hdrc musb-hdrc.0: MUSB HDRC host driver
[ 65.339317] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1
[ 65.455488] hub 1-0:1.0: USB hub found
[ 65.526286] hub 1-0:1.0: 1 port detected
[ 65.945162] using random self ethernet address
[ 65.981243] using random host ethernet address
[ 66.030043] using host ethernet address: 88:33:14:FC:CA:1A[ 66.103763] using random self ethernet address
[ 66.153245] using random host ethernet address
[ 66.215896] using host ethernet address: 88:33:14:FC:CA:1A[ 66.315993] usb0: HOST MAC 88:33:14:fc:ca:1a
[ 66.379246] usb0: MAC 16:06:4c:1c:e5:21
[ 66.753252] Mass Storage Function, version: 2009/09/11
[ 66.797376] LUN: removable file: (no medium)
[ 66.862339] LUN: removable read only file: /dev/mmcblk0p1
[ 66.926010] Number of LUNs=1
[ 66.948992] g_multi gadget: Multifunction Composite Gadget
[ 66.954629] g_multi gadget: g_multi ready
[ 67.431382] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[ 67.496013] usb 1-1: new full-speed USB device number 2 using musb-hdrc
[ 67.628378] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2
[ 67.768995] hub 2-0:1.0: USB hub found
[ 67.812214] hub 2-0:1.0: 1 port detected
***************************************************************
***************************************************************
NOTICE: This file system contains the following GPLv3 packages:
autoconf
binutils
cifs-utils
cpp-symlinks
cpp
dosfstools
g++-symlinks
g++
gawk-dev
gawk
gcc-symlinks
gcc
gdb
gdbserver
glmark2
gstreamer1.0-libav
hidapi
libcairo-perf-utils
libgmp10
libidn11
libmpc3
libmpfr4
libreadline-dev
libreadline6
m4-dev
m4
make
nettle
swig-dev
swig
If you do not wish to distribute GPLv3 components please remove
the above packages prior to distribution. This can be done using
the opkg remove command. i.e.:
opkg remove <package>
Where <package> is the name printed in the list above
NOTE: If the package is a dependency of another package you
will be notified of the dependent packages. You should
use the --force-removal-of-dependent-packages option to
also remove the dependent packages as well
***************************************************************
***************************************************************
[ 89.901029] pvrsrvkm: disagrees about version of symbol dev_err
[ 89.907619] pvrsrvkm: Unknown symbol dev_err (err -22)
_____ _____ _ _
| _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_
| | _| .'| . | . | | __| _| . | | | -_| _| _|
|__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_|
|___| |___|
Arago Project http://arago-project.org am335x-evm ttyS0
Arago 2017.10 am335x-evm ttyS0
am335x-evm login: root
[ 96.003116] pvrsrvkm: disagrees about version of symbol dev_err
[ 96.066003] pvrsrvkm: Unknown symbol dev_err (err -22)
root@am335x-evm:~#
root@am335x-evm:~# ifconfig
eth0 Link encap:Ethernet HWaddr 88:33:14:FC:CA:18
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:2338 (2.2 KiB)
Interrupt:171
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:480 errors:0 dropped:0 overruns:0 frame:0
TX packets:480 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:36480 (35.6 KiB) TX bytes:36480 (35.6 KiB)
usb0 Link encap:Ethernet HWaddr 16:06:4C:1C:E5:21
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@am335x-evm:~# ifconfig -a
eth0 Link encap:Ethernet HWaddr 88:33:14:FC:CA:18
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:2338 (2.2 KiB)
Interrupt:171
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:640 errors:0 dropped:0 overruns:0 frame:0
TX packets:640 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:48640 (47.5 KiB) TX bytes:48640 (47.5 KiB)
usb0 Link encap:Ethernet HWaddr 16:06:4C:1C:E5:21
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
root@am335x-evm:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 1
Transceiver: external
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000000 (0)
Link detected: yes
root@am335x-evm:~# ethtool -S eth0
NIC statistics:
Good Rx Frames: 0
Broadcast Rx Frames: 0
Multicast Rx Frames: 0
Pause Rx Frames: 0
Rx CRC Errors: 0
Rx Align/Code Errors: 0
Oversize Rx Frames: 0
Rx Jabbers: 0
Undersize (Short) Rx Frames: 0
Rx Fragments: 0
Rx Octets: 0
Good Tx Frames: 8
Broadcast Tx Frames: 8
Multicast Tx Frames: 0
Pause Tx Frames: 0
Deferred Tx Frames: 0
Collisions: 0
Single Collision Tx Frames: 0
Multiple Collision Tx Frames: 0
Excessive Collisions: 0
Late Collisions: 0
Tx Underrun: 0
Carrier Sense Errors: 0
Tx Octets: 2704
Rx + Tx 64 Octet Frames: 0
Rx + Tx 65-127 Octet Frames: 0
Rx + Tx 128-255 Octet Frames: 0
Rx + Tx 256-511 Octet Frames: 8
Rx + Tx 512-1023 Octet Frames: 0
Rx + Tx 1024-Up Octet Frames: 0
Net Octets: 2704
Rx Start of Frame Overruns: 0
Rx Middle of Frame Overruns: 0
Rx DMA Overruns: 0
Rx DMA chan 0: head_enqueue: 1
Rx DMA chan 0: tail_enqueue: 127
Rx DMA chan 0: pad_enqueue: 0
Rx DMA chan 0: misqueued: 0
Rx DMA chan 0: desc_alloc_fail: 0
Rx DMA chan 0: pad_alloc_fail: 0
Rx DMA chan 0: runt_receive_buf: 0
Rx DMA chan 0: runt_transmit_bu: 0
Rx DMA chan 0: empty_dequeue: 0
Rx DMA chan 0: busy_dequeue: 0
Rx DMA chan 0: good_dequeue: 0
Rx DMA chan 0: requeue: 0
Rx DMA chan 0: teardown_dequeue: 0
Tx DMA chan 0: head_enqueue: 8
Tx DMA chan 0: tail_enqueue: 0
Tx DMA chan 0: pad_enqueue: 0
Tx DMA chan 0: misqueued: 0
Tx DMA chan 0: desc_alloc_fail: 0
Tx DMA chan 0: pad_alloc_fail: 0
Tx DMA chan 0: runt_receive_buf: 0
Tx DMA chan 0: runt_transmit_bu: 0
Tx DMA chan 0: empty_dequeue: 8
Tx DMA chan 0: busy_dequeue: 0
Tx DMA chan 0: good_dequeue: 8
Tx DMA chan 0: requeue: 0
Tx DMA chan 0: teardown_dequeue: 0
root@am335x-evm:~#
Part Number:DAC37J82EVM
Please pardon my ignorance! I would like to generate a ~375MHz tone out the DAC. It seems that the Quick Start files are limited to ~200MHz. Is there an easy way to generate and program the files necessary for the 375MHz tone? I looked through the documentation, but couldn't find anything.
Part Number:DLPDLCR2000EVM
Tool/software: Linux
Hi
Trying to connect the EVM to a raspberry pi following the steps by Philip https://e2e.ti.com/support/dlp__mems_micro-electro-mechanical_systems/video_and_data_display/f/947/p/651931/2395243?tisearch=e2e-sitesearch&keymatch=DLPDLCR2000EVM%20i2c#2395243
Part Number:ADC12DJ3200EVM
Hi
My system connfiguration is:
5 GSPS, JMODE 0
Linerate 10 Gbps, refclk 500 MHz, core:clk 250 MHz, no scrambler, K=4, I changed RX ¨polarity for DB0-DB3 lanes
I tested system by Ramp mode and it looks OK.
I also tried K28.5 mode, it also looks OK:
But in normal mode, i think that i get a wrong data on rx, actually I have no input signal (offset is set to 20 mV):
what may be wrong?
Part Number:TPS92310-12FB
Dear Sir:
Does TPS92310-12FB EVM can support AC TRIAC dimming control?
Best Regard
Jason
Part Number:BQ34Z100EVM
Hi,
I've been following the step-by-step design procedure, chapter 8.2.2.1 from the datasheet and always (but once) come to a stop at the calibration. One of the first times it worked, but I don't know what I did different.
I've tried some different options and changed the order, even changed a BQstudio config file I found here on the forum. During the data changes the measured voltage already changes from about 240 mV to 4000+ mv. But it is still about a 1000 mV off.
I've been to default a few times and sometimes come to different problems. But mostly that the data is out of range.
Sometimes BQstudio looks completely different on the top and has a lot more options, the calibrate fault I get is a acknowledge problem from the device, and the image on the side shows "zzz" asleep. Will make a screenshot when it happens again.
The attached documents is my last try. I started from default and wrestled through the datasheet step-by-step. When I started all the external lights on the EVM were on, somewhere on the route they all went off, the voltage is 4312mV, but in reality it is 5220mV.
Thanks in advance,
Karolijn
Registers
Calibration
* Texas Instruments Data Flash File
* File created Fri Mar 16 13:55:36 2018
*
* Device Number 100
* Firmware Version 0.16
* Build Number not available
* Order Number not available
*
* bqz Device Number 100
* bqz Firmware Version 0.16
* bqz Build Number 17
*
* Field Order: Class name, Subclass name, Parameter name, Parameter Value, Display Units
"Configuration","Safety","OT Chg","55.0","1degC"
"Configuration","Safety","OT Chg Time","2","Seconds"
"Configuration","Safety","OT Chg Recovery","50.0","1degC"
"Configuration","Safety","OT Dsg","60.0","1degC"
"Configuration","Safety","OT Dsg Time","2","Seconds"
"Configuration","Safety","OT Dsg Recovery","55.0","1degC"
"Configuration","Charge Inhibit Cfg","Chg Inhibit Temp Low","0","1degC"
"Configuration","Charge Inhibit Cfg","Chg Inhibit Temp High","45.0","1degC"
"Configuration","Charge Inhibit Cfg","Temp Hys","5.0","1degC"
"Configuration","Charge","Suspend Low Temp","-5.0","1degC"
"Configuration","Charge","Suspend High Temp","55.0","1degC"
"Configuration","Charge","Pb EFF Efficiency","100","%"
"Configuration","Charge","Pb Temp Comp","24.960","%"
"Configuration","Charge","Pb Drop Off Percent","96","%"
"Configuration","Charge","Pb Reduction Rate","10.000","%"
"Configuration","Charge Termination","Taper Current","100","mAmp"
"Configuration","Charge Termination","Min Taper Capacity","25","mAmpHr"
"Configuration","Charge Termination","Cell Taper Voltage","100","mVolt"
"Configuration","Charge Termination","Current Taper Window","40","Seconds"
"Configuration","Charge Termination","TCA Set %","99","Percent"
"Configuration","Charge Termination","TCA Clear %","95","Percent"
"Configuration","Charge Termination","FC Set %","100","Percent"
"Configuration","Charge Termination","FC Clear %","98","Percent"
"Configuration","Charge Termination","DODatEOC Delta T","10.0","1degC"
"Configuration","Charge Termination","NiMH Delta Temp","3.0","1degC"
"Configuration","Charge Termination","NiMH Delta Temp Time","180","Seconds"
"Configuration","Charge Termination","NiMH Hold Off Time","100","Seconds"
"Configuration","Charge Termination","NiMH Hold Off Current","240","mAmp"
"Configuration","Charge Termination","NiMH Hold Off Temp","25.0","1degC"
"Configuration","Charge Termination","NiMH Cell Negative Delta Volt","17","mVolt"
"Configuration","Charge Termination","NiMH Cell Negative Delta Time","16","Seconds"
"Configuration","Charge Termination","NiMH Cell Neg Delta Qual Volt","4200","mVolt"
"Configuration","Data","Manufacture Date","1980-1-1","Day + Mo*32 + (Yr -1980)*256"
"Configuration","Data","Serial Number","0001","hex"
"Configuration","Data","Cycle Count","0","Count"
"Configuration","Data","CC Threshold","900","mAmpHr"
"Configuration","Data","Max Error Limit","100","%"
"Configuration","Data","Design Capacity","2500","MilliAmpHour"
"Configuration","Data","Design Energy","12000","MilliWattHour"
"Configuration","Data","SOH Load I","-400","MilliAmp"
"Configuration","Data","Cell Charge Voltage T1-T2","4200","mV"
"Configuration","Data","Cell Charge Voltage T2-T3","4200","mV"
"Configuration","Data","Cell Charge Voltage T3-T4","4100","mV"
"Configuration","Data","Charge Current T1-T2","10","Percent"
"Configuration","Data","Charge Current T2-T3","50","Percent"
"Configuration","Data","Charge Current T3-T4","30","Percent"
"Configuration","Data","JEITA T1","0","degC"
"Configuration","Data","JEITA T2","10","degC"
"Configuration","Data","JEITA T3","45","degC"
"Configuration","Data","JEITA T4","55","degC"
"Configuration","Data","Design Energy Scale","1","Number"
"Configuration","Data","Device Name","bq34z100-G1","-"
"Configuration","Data","Manufacturer Name","Texas Inst.","-"
"Configuration","Data","Device Chemistry","LION","-"
"Configuration","Discharge","SOC1 Set Threshold","150","mAh"
"Configuration","Discharge","SOC1 Clear Threshold","175","mAh"
"Configuration","Discharge","SOCF Set Threshold","75","mAh"
"Configuration","Discharge","SOCF Clear Threshold","100","mAh"
"Configuration","Discharge","Cell BL Set Volt Threshold","2800","mVolt"
"Configuration","Discharge","Cell BL Set Volt Time","2","Seconds"
"Configuration","Discharge","Cell BL Clear Volt Threshold","2900","mVolt"
"Configuration","Discharge","Cell BH Set Volt Threshold","4300","mVolt"
"Configuration","Discharge","Cell BH Volt Time","2","Seconds"
"Configuration","Discharge","Cell BH Clear Volt Threshold","4200","mVolt"
"Configuration","Discharge","Cycle Delta","0.05","%"
"Configuration","Manufacturer Data","Pack Lot Code","0000","hex"
"Configuration","Manufacturer Data","PCB Lot Code","0000","hex"
"Configuration","Manufacturer Data","Firmware Version","0000","hex"
"Configuration","Manufacturer Data","Hardware Revision","0000","hex"
"Configuration","Manufacturer Data","Cell Revision","0000","hex"
"Configuration","Manufacturer Data","DF Config Version","0000","hex"
"Configuration","Lifetime Data","Lifetime Max Temp","30.0","1degC"
"Configuration","Lifetime Data","Lifetime Min Temp","20.0","1degC"
"Configuration","Lifetime Data","Lifetime Max Chg Current","0","mAmp"
"Configuration","Lifetime Data","Lifetime Max Dsg Current","0","mA"
"Configuration","Lifetime Data","Lifetime Max Pack Voltage","160","20mV"
"Configuration","Lifetime Data","Lifetime Min Pack Voltage","175","20mV"
"Configuration","Lifetime Temp Samples","LT Flash Cnt","0","Count"
"Configuration","Registers","Pack Configuration","49d9","flags"
"Configuration","Registers","Pack Configuration B","af","flags"
"Configuration","Registers","Pack Configuration C","37","flags"
"Configuration","Registers","LED_Comm Configuration","a3","flags"
"Configuration","Registers","Alert Configuration","0000","flags"
"Configuration","Registers","Number of series cell","4","num"
"Configuration","Lifetime Resolution","LT Temp Res","1.0","1degC"
"Configuration","Lifetime Resolution","LT Cur Res","100","mA"
"Configuration","Lifetime Resolution","LT V Res","1","20mV"
"Configuration","Lifetime Resolution","LT Update Time","60","Seconds"
"Configuration","LED Display","LED Hold Time","4","Num"
"Configuration","Power","Flash Update OK Cell Volt","3500","mVolt"
"Configuration","Power","Sleep Current","10","mAmp"
"Configuration","Power","FS Wait","0","Seconds"
"System Data","Manufacturer Info","Block A 0","00","hex"
"System Data","Manufacturer Info","Block A 1","00","hex"
"System Data","Manufacturer Info","Block A 2","00","hex"
"System Data","Manufacturer Info","Block A 3","00","hex"
"System Data","Manufacturer Info","Block A 4","00","hex"
"System Data","Manufacturer Info","Block A 5","00","hex"
"System Data","Manufacturer Info","Block A 6","00","hex"
"System Data","Manufacturer Info","Block A 7","00","hex"
"System Data","Manufacturer Info","Block A 8","00","hex"
"System Data","Manufacturer Info","Block A 9","00","hex"
"System Data","Manufacturer Info","Block A 10","00","hex"
"System Data","Manufacturer Info","Block A 11","00","hex"
"System Data","Manufacturer Info","Block A 12","00","hex"
"System Data","Manufacturer Info","Block A 13","00","hex"
"System Data","Manufacturer Info","Block A 14","00","hex"
"System Data","Manufacturer Info","Block A 15","00","hex"
"System Data","Manufacturer Info","Block A 16","00","hex"
"System Data","Manufacturer Info","Block A 17","00","hex"
"System Data","Manufacturer Info","Block A 18","00","hex"
"System Data","Manufacturer Info","Block A 19","00","hex"
"System Data","Manufacturer Info","Block A 20","00","hex"
"System Data","Manufacturer Info","Block A 21","00","hex"
"System Data","Manufacturer Info","Block A 22","00","hex"
"System Data","Manufacturer Info","Block A 23","00","hex"
"System Data","Manufacturer Info","Block A 24","00","hex"
"System Data","Manufacturer Info","Block A 25","00","hex"
"System Data","Manufacturer Info","Block A 26","00","hex"
"System Data","Manufacturer Info","Block A 27","00","hex"
"System Data","Manufacturer Info","Block A 28","00","hex"
"System Data","Manufacturer Info","Block A 29","00","hex"
"System Data","Manufacturer Info","Block A 30","00","hex"
"System Data","Manufacturer Info","Block A 31","00","hex"
"Gas Gauging","IT Cfg","Load Select","1","Number"
"Gas Gauging","IT Cfg","Load Mode","0","Number"
"Gas Gauging","IT Cfg","Res Current","10","mAmp"
"Gas Gauging","IT Cfg","Max Res Factor","15","num"
"Gas Gauging","IT Cfg","Min Res Factor","3","num"
"Gas Gauging","IT Cfg","Ra Filter","500","num"
"Gas Gauging","IT Cfg","Min PassedChg NiMH-LA 1st Qmax","50","%"
"Gas Gauging","IT Cfg","Maximum Qmax Change","100","%"
"Gas Gauging","IT Cfg","Cell Terminate Voltage","3000","mVolt"
"Gas Gauging","IT Cfg","Cell Term V Delta","200","mVolt"
"Gas Gauging","IT Cfg","ResRelax Time","500","Seconds"
"Gas Gauging","IT Cfg","User Rate-mA","0","MilliAmp"
"Gas Gauging","IT Cfg","User Rate-Pwr","0","mW/cW"
"Gas Gauging","IT Cfg","Reserve Cap-mAh","0","MilliAmpHour"
"Gas Gauging","IT Cfg","Reserve Energy","0","mWh/cWh"
"Gas Gauging","IT Cfg","Max Scale Back Grid","4","num"
"Gas Gauging","IT Cfg","Cell Min DeltaV","0","mVolt"
"Gas Gauging","IT Cfg","Ra Max Delta","15","%"
"Gas Gauging","IT Cfg","Design Resistance","42","mOhms"
"Gas Gauging","IT Cfg","Reference Grid","4","-"
"Gas Gauging","IT Cfg","Qmax Max Delta %","10","mAmpHour"
"Gas Gauging","IT Cfg","Max Res Scale","5000","Num"
"Gas Gauging","IT Cfg","Min Res Scale","200","Num"
"Gas Gauging","IT Cfg","Fast Scale Start SOC","10","%"
"Gas Gauging","IT Cfg","Charge Hys V Shift","40","mVolt"
"Gas Gauging","IT Cfg","Smooth Relax Time","1000","s"
"Gas Gauging","Current Thresholds","Dsg Current Threshold","60","mAmp"
"Gas Gauging","Current Thresholds","Chg Current Threshold","75","mAmp"
"Gas Gauging","Current Thresholds","Quit Current","10","mAmp"
"Gas Gauging","Current Thresholds","Dsg Relax Time","60","Seconds"
"Gas Gauging","Current Thresholds","Chg Relax Time","60","Seconds"
"Gas Gauging","Current Thresholds","Cell Max IR Correct","400","mV"
"Gas Gauging","State","Qmax Cell 0","2500","mAmpHr"
"Gas Gauging","State","Cycle Count","0","num"
"Gas Gauging","State","Update Status","00","num"
"Gas Gauging","State","Cell V at Chg Term","4200","mVolt"
"Gas Gauging","State","Avg I Last Run","-299","mAmp"
"Gas Gauging","State","Avg P Last Run","-1131","MilliWattHour"
"Gas Gauging","State","Cell Delta Voltage","2","mVolt"
"Gas Gauging","State","T Rise","20","Num"
"Gas Gauging","State","T Time Constant","1000","Num"
"Ra Tables","Ra0 Table","Ra Flag","ff55","Hex"
"Ra Tables","Ra0 Table","Ra 0","105","Num"
"Ra Tables","Ra0 Table","Ra 1","100","Num"
"Ra Tables","Ra0 Table","Ra 2","113","Num"
"Ra Tables","Ra0 Table","Ra 3","143","Num"
"Ra Tables","Ra0 Table","Ra 4","98","Num"
"Ra Tables","Ra0 Table","Ra 5","97","Num"
"Ra Tables","Ra0 Table","Ra 6","108","Num"
"Ra Tables","Ra0 Table","Ra 7","89","Num"
"Ra Tables","Ra0 Table","Ra 8","86","Num"
"Ra Tables","Ra0 Table","Ra 9","85","Num"
"Ra Tables","Ra0 Table","Ra 10","87","Num"
"Ra Tables","Ra0 Table","Ra 11","90","Num"
"Ra Tables","Ra0 Table","Ra 12","110","Num"
"Ra Tables","Ra0 Table","Ra 13","647","Num"
"Ra Tables","Ra0 Table","Ra 14","1500","Num"
"Ra Tables","Ra0x Table","Ra Flag","ffff","Hex"
"Ra Tables","Ra0x Table","Ra 0","105","Num"
"Ra Tables","Ra0x Table","Ra 1","100","Num"
"Ra Tables","Ra0x Table","Ra 2","113","Num"
"Ra Tables","Ra0x Table","Ra 3","143","Num"
"Ra Tables","Ra0x Table","Ra 4","98","Num"
"Ra Tables","Ra0x Table","Ra 5","97","Num"
"Ra Tables","Ra0x Table","Ra 6","108","Num"
"Ra Tables","Ra0x Table","Ra 7","89","Num"
"Ra Tables","Ra0x Table","Ra 8","86","Num"
"Ra Tables","Ra0x Table","Ra 9","85","Num"
"Ra Tables","Ra0x Table","Ra 10","87","Num"
"Ra Tables","Ra0x Table","Ra 11","90","Num"
"Ra Tables","Ra0x Table","Ra 12","110","Num"
"Ra Tables","Ra0x Table","Ra 13","647","Num"
"Ra Tables","Ra0x Table","Ra 14","1500","Num"
"Calibration","Data","CC Gain","10.123","mohm"
"Calibration","Data","CC Delta","10.147","mohm"
"Calibration","Data","CC Offset","-1296","num"
"Calibration","Data","Board Offset","0","num"
"Calibration","Data","Int Temp Offset","0","degC"
"Calibration","Data","Ext Temp Offset","0","degC"
"Calibration","Data","Voltage Divider","16000","mVolt"
"Calibration","Current","Deadband","5","mAmp"
"Security","Codes","Sealed to Unsealed","36720414","hex"
"Security","Codes","Unsealed to Full","ffffffff","hex"
"Security","Codes","Authen Key3","01234567","hex"
"Security","Codes","Authen Key2","89abcdef","hex"
"Security","Codes","Authen Key1","fedcba98","hex"
"Security","Codes","Authen Key0","76543210","hex"
Tool/software: Code Composer Studio
Hi guys,
I would like to know how to obtain CCS 4.2.5 full install, not the update, as that does not work for some strange reason.
Thanks