Part Number:TUSB1046-DCI
Hi Team,
My customer considers to use TUSB1046 for notebook application.
Is there CAD design file (component library) for TUSB1046?
Best Regards,
Yaita / Japan disty
↧
TUSB1046-DCI: CAD design file for TUSB1046
↧
CC2650RC: RemoTI Target Emulator Users Guide (SWRU202 - Equivalent)
Part Number:CC2650RC
Hello All,
For the CC2650RC, I am looking for the RemoTI Target Emulator Users Guide.
In the past, for the CC2533 RF4CE, it is documented to have been as follows from SWRU266A page 14, Section 4.8:
"The target emulator can be found in the <Installation Path>\RemoTI\bin folder. For instructions on how to
set up and use the target emulator please see the RemoTI Target Emulator Users Guide (SWRU202) in
the <Installation Path>\Documents\User Guide folder."
Where can one find a similar document for the CC2650 RC?
Thanks,
Manuel
↧
↧
WL1807MOD: Evaluating WL18xx over Ethernet
Part Number:WL1807MOD
Hi Team,
Is there a way to route data over an ethernet port to do performance testing on our WL18xx eval kits? I assume that we will need some sort of host processor eval board, so I was thinking we could use a BeagleBone + WiLink cape, but I would like to see what other options our customers may have.
Appreciate the support.
↧
TMS570LS3137: About Information Redundancy Techniques - L2/L3 Interconnect Specific
Part Number:TMS570LS3137
Information Redundancy Techniques - We are considering adopting L2 / L3 Interconnect Specific.
I do not know the peripheral connected to L2 / L3.
Specifically, which peripheral are covered with L2 / L3 interconnect?
↧
TLC59582: Reference Board and Example Code.
↧
↧
TPA3255: Input bias level
Part Number:TPA3255
The only spec I could find regarding the input voltage level is the maximum input voltage swing, peak - peak of 7 volts. What voltage is this swing with respect to? I'm guessing it's 4 volts above ground.
↧
TMS320F28375S: About mapping from logical address to "EMIF2" pins for 16-bit SDRAM
Part Number:TMS320F28375S
Hello.
I have two questions.
1.Is it correct to confirm the table 24-15,page 2302, in the technical reference manual when I use EMIF2?
2.Is it possible to access the address space described in the table 24-15,page 2302, in the technical reference manual when I use EMIF2?
About table 24-15,page 2302, in the technical reference manual, it seems to described Row Address as 13bit.
But TMS320F28375s has only 12 EM2A pins according to the device specific datasheet.
Would you give me any advises?
Regards,
uchida-k
↧
LMR14030-Q1: CISPR25
Part Number:LMR14030-Q1
Hi,
I received the following question from my customer.
Has the application which used the LMR14030-Q1 with SS/non-SS passed the CSPR25?
Best Regards,
Kuramochi
↧
MSP430G2553: TMP007 + MSP430 + CC2650
Part Number:MSP430G2553
I have made a schematic wherein i read temperature from TMP007 sensor via MSP430 and then transfer the data to CC2650 through UART which in turn broadcasts
through BLE medium.
Please have a look at the circuit and give your feedback.
↧
↧
WILINK-BT_WIFI-WIRELESS_TOOLS: HCITester problem
Part Number: WILINK-BT_WIFI-WIRELESS_TOOLS
I have Ti Arago linux running on BBB and am able to control Element14 WL1837 BT communication via Ti Bluetopia, but could not make HCITester work with the same wilink cape by following hcitester user guide.
I am certain that BT_EN = 1. I've tried connecting and disconnecting BBB HCI lines to Wilink when using HCITester + USB/Serial calbe, but failed in both cases. TIInit_11.8.32.bts is the initialization BT script I used.
In other words, after verifying BT working conditions of BBB+Element14 WL1837 cape, I replace BBB HCI lines with 3.3V USB/serial lines, but still leave the rest connections (jump wires) from BBB to wilink. When executing BT initialization script .bts, HCITester always times out in the step of setting baud rate at the very beginning.
What am I missing?
Thanks,
Buli
↧
TPA2000D1: thermal shutdown
↧
SN65HVD251: The problem of difference of time between high level and low level
Part Number:SN65HVD251
Dear,
We test SN65HVD251DR and find that the time of high level is 4.6 us and the time of low level is 3.4 us. We hope that when the frequency is 250 KHz, the bit time is 4 us, and the time of high level is equal to the time of low level, the error range of bit time is 0.2% ( the average of tested 10 levels when transmitting data ). So is the next waveform normal? Could you provide the waveform of SN65HVD251DR that TI tested? How to adjust parameters to make the time of high level be equal to the time of low level?
The waveform and the schematic as follows. I am waiting your reply, thank you!
↧
RTOS/MSP430F5659: TASK_STAT need info
Part Number:MSP430F5659
Tool/software: TI-RTOS
Hi,
I am using Task_stat() function to read the task stack usage, want to understand whether this API makes any interrupt disable/enable handling?
Even some time i found that address violation error while execution of the this API.
Please help me, i want to handle the address violation error ?
since i am using 4 task , Can i call this function in one place to read the stack usage? currently i am calling task_stat() @ every task end to read the stack usage.
Thanks in advance,
Nitesh
↧
↧
LDC1312: TIDU952 output data with stable state
Part Number:LDC1312
Hi Team,
Regarding TIDU952, I got following questions so could you help me?
Question
Max/Min angular position accuracy at stable situation.
Following is test condition
1. Put TIDU953 on table(no effected from external objects)
2. Read TIDU953 Angular position data
3. investigate how output angular position data changes from ideal value.
e.g.
put TIDU953 on table with 0 position
read angular position from TIDU953
investigate how output angular position data changes from 0 position.
Thanks,
Regards,
Kai
↧
CC1310: DCDC_SW LC layout options
Part Number:CC1310
I want to acknowledge the recommendation to follow the reference design for layouts; however I am have a space constraint and looking to explore options.
We are trying to fit our design/layout under a shield and are running into a space constraint; an area that I was looking to gain some space is around the DCDC_SW pins. Is it possible, with a reasonable expectation of success, to place the inductor and capacitors for the DCDC_SW on the bottom layer under these pins and obviously connect them through vias. Any guidance or recommendation would be appreciated.
Gary
↧
Circuitry required to convert single ended signal to differential signal for 16-bit ADC
Part Number:TMS320F28377D
Hi All,
I am using TMS320F28377D for my inverter application. I need to use 16-bit ADC to get precise result. I have single ended input signal but 16-bit ADC only used in differential mode. So, my first requirement is to convert single ended signal into differential signal. Kindly suggest circuitry for the same.
I have to maintain constant 1.65 common mode voltage. For example, My single ended input is 2.2V then my differential signal output should be Vin+ = 2.2V and Vin- = 1.1V.
Vcm = (Vin+ + Vin-)/2 = (2.2 + 1.1)/2 = 1.65V.
Thanks and regards,
Maulik Timbadiya
↧
ULN2003A: Absolute Maximum Rating of TA
Part Number:ULN2003A
ULN2003A absolute maximum rating of TA is -20 degC to 70 degC. And Recommended Operating condition Tj is -40 degC to 125 degC.
Should we use ULN2003A within TA -20 degC to 70 degC even if device power consumption is low and Tj is not over 125 degC?
Using condition is the following,
1ch to 4ch: 7mA at each ch
6ch: 120mA
5ch, 7ch: not used
Best Regards,
Kohei Sasaki
↧
↧
SUITABLE FIRMWARE VERSION FOR CC3000 WIFI MODULE
Will different CC3000 hardware chip will support different firmware version or every CC3000 module will support the latest firmware version 1.14
↧
CC3100MOD: Setup STATION SSID and and PASSWORD througth internal webserver
Part Number:CC3100MOD
Hi,
in our application we would like to use the web server to configure the STATION mode as follows
1) user start CC3100 as a Open AP and with the internal web server set SSID and Password
2) After a power cycle, module starts as station with selected password and SSID
Is this possible with embedded webserver ? Note that, unfortunately, we could not upgrade CC3100MOD file system with custom due hardware design, so we must use the internal webserwer with rom suplied pages.
Thanks
Giuseppe Monteleone
↧
TMS320C6727B: Evaluation board schematic
Part Number:TMS320C6727B
Where can I obtain a copy of the schematic for the (now obsolete) evaluation module for the TMS320C6727, originally developed by DSP-Weuffen? I am also interested in obtaining other documentation and software, including the parts list and PCB layout information. Thanks!
↧
