TL1431-SP: Recommended NC connections
Part Number:TL1431-SPHello,Can you confirm that the NC pins on this device are truly not connected to the die?We cannot leave these pins floating. Is there a recommendation for this? Can we connect...
View ArticleClik here to view.
ADS8168: Determining RC Filter Values for INA190A4 and ADS8168
(Please visit the site to view this file)Part Number:ADS8168Hi there,I was planning to implement a uni-directional current sensing circuit as per attached TINA circuit schematic. I was wondering if the...
View ArticleCCS/TMS320F28377S: Determine the cause of error
Part Number:TMS320F28377STool/software: Code Composer StudioHow to determine the cause of error in the reset handler ? I use reset by watchdog
View ArticleUCC28780: Questions about SLUC664 spreadsheet
Part Number:UCC28780I don't understand a couple of the data inputs in the SLUC664 design calculator spreadsheet for this IC:What should I use for "Input Voltage BUR, VINPUT_BUR"? The data sheet in...
View ArticleINA240: INA240A2 stuck at ground with Vcm = 0
Part Number:INA240I have designed a board with many INA240A2 for current sensing. Some, but not all of the parts will power up with the output ground. The output should be at 1.024V due to a 2.048V...
View ArticleBQ20Z655-R1: Calibration and Addresses
Part Number:BQ20Z655-R1Hi Batt,I am trying to read and load the settings from and to the BMS. The calibration document says to read and write all the data in dataflash from offset 0x4000 to 0x4700,...
View ArticleCC2640R2F: Can't connect to iOS 12 (likely is because of heap issue)
Part Number:CC2640R2FSDK 1.40.00.45My firmware is working fine with iOS10 until the version has changed to iOS12. I found that it may be related to the heap problem. Making a connection with iOS12...
View ArticleDLP2010NIR: Wavelength clarification
Part Number:DLP2010NIRHi,We are planning to use DLP2010NIR for one of our food analysis and i'm not getting the exact spectral range. Will this support up 700nm to 1700nm or can we go up to 2000nm. We...
View ArticleMSP430F5529: MSP430F5529 - Labview VI modules
Part Number:MSP430F5529Hi,I am working on a basic application which uses the MSP430F5529LP and a Labview GUI that will talk to each other via USB module in a half-duplex fashion. I know that the...
View ArticleClik here to view.
DRV8353R: Increase gate drive capability with additional gate driver
Part Number:DRV8353RHi,in my master thesis I want to parallelize two Mosfets (FDBL0200N100) with a total gate charge of 266nC (each 133nC for worst case) at 30kHz in a 48V 1.5kW three phase inverter....
View ArticleTPS2372-4EVM-006: Bulk capacitor
Part Number:TPS2372-4EVM-006Hi All,I'm developing a board based on the circuit reference of TPS2372-4EVM-006 and the bulk capacitor of 100uf doesn't fit at all in the board. I can't even fit 2 of 47uF...
View ArticleSM320C6727B-EP: Powering device above recommended operating voltage but below...
Part Number:SM320C6727B-EPI am working a design that incorporates the Microchip RT3 Proasic SOC chip mated up to the TMS320C6727B-SP DSP. To perform in--system programming of the SOC device, I need to...
View ArticleClik here to view.
CCS/LAUNCHXL-CC2650: printf does not display
Part Number:LAUNCHXL-CC2650Tool/software: Code Composer StudioHello,How can I print values on the console? It doesnot print anything even though use printf(). Here is the
View ArticleCCS/TMS320F28035: Issue with CCS V.7 Debugger
Part Number:TMS320F28035Tool/software: Code Composer StudioHi, AllI need help from the TI team, becauase a I have issue with the CCS V.7 and Experimenter kit to TMS320F28035.I have a program where I...
View ArticleRTOS/BLE-STACK: I can't to build the simple peripheral example.
Part Number:BLE-STACKTool/software: TI-RTOSI can't to build the simple peripheral example. I am using IAR 7.50.2 and TI BLE Stack SDK 2.02.02.25. I think that there are a problem with the argument...
View ArticleBQ34110: I2C Address Change
Part Number:BQ34110Hello,In the TRM, it says that the I2C address of the BQ34110 is fixed at 0b10101. If we wanted to connect multiple BQ34110s to the same host, is there any way that we can change the...
View ArticleADC32RF45EVM: High Speed Data Converter (HSDC) Pro Software Output Binary...
Part Number:ADC32RF45EVMHello,I'm using the HSDC Pro software and I have to pass the output/acquired binary data to MATLAB for processing. I'm looking through the HSDC Pro Software documentation and...
View ArticleCC3120BOOST: How to change WiFi host driver SPI settings
Part Number:CC3120BOOSTHello,We are trying to change default SPI settings used by the WiFi host driver from the user application, but cannot call SPI_Params_init and SPI_open due to instance...
View ArticleRTOS/MSP430FR5994: MSP430FR5994, ADC returns max values after BIOS_start()
Part Number:MSP430FR5994Tool/software: TI-RTOSHello,I am trying to implement TI example msp430fr599x_adc12_02.c into my project. I get reasonable values if I read the ADC before BIOS_start(). But if...
View ArticleLAUNCHXL-CC1310: How to compare received RF data to a number/hex value on...
Part Number:LAUNCHXL-CC1310I have this section where I receive the data. The data even prints on the UART properly everything works. Now I want to add comparison to this received data. So if I receive...
View Article