CCS/AM5728: Tool for code migration from C2000 to C66x
Part Number:AM5728Tool/software: Code Composer StudioDear Sir,Customers who are using C2000 and have developed planning of motion trajectory and control theory on C2000 for long time.Currently, they...
View ArticleCC2592: RF input of CC2592 is balance architecture. Can it work in...
Part Number:CC2592Dear Sir,RF input of CC2592 is balance architecture. Can it work in un-balance? If yes, how can it be performed. Thanks!
View ArticleClik here to view.
RTOS/AM5728: A exception happened when TI-RTOS continuous running
Part Number:AM5728Tool/software: TI-RTOSI have created a project which include taking photo, uploading photo by ethernet, Identifing the image, and upload the result by ethernet and uart. When the...
View ArticleCCS/TMS320F28377D: CPU1 flash standalone and CPU2 flash code stuck during...
Part Number:TMS320F28377DTool/software: Code Composer StudioHi.I stumbled in a situation where my RAM and FLASH code, started by emulator and loaded in CPU1+CLA and CPU2+CLA, running well but...
View Articlequestion about CC1310 discrete PA
In SWRA490,I know this design is for a frequency range of 470 MHz to 510 MHz, and it mentioned that "If a different frequency than 470 – 510 MHz or higher output power (> 22 dBm) is required, then...
View ArticleTPS92692-Q1: TPS92692-Q1 Duty and PWM Question
Part Number:TPS92692-Q1Hi Team,I have question about duty cycle and Analot-to-PWM dimming relative of TPS92692-Q1.In my case, designed the DRL/PL current be 140mA/10mA. 1. May I know the 4% accuracy...
View ArticleIWR6843ISK: 3.3V Power consumption(Max, Typ) of IWR6843ISK
Part Number:IWR6843ISKTo whom may it concern,I'd like to know what is consumed 3.3V Power power(current) of IWR6843ISK (not IWR6843 IC only).Max. Current and Typ. Current in harsh situation(Full power...
View ArticleRTOS/LAUNCHCC3220MODASF: UART0 and UART1 at the same time
Part Number:LAUNCHCC3220MODASFTool/software: TI-RTOSHello,I want to use UART0 and UART1 at the same time. Is this possible with the LaunchPad Development Kit Board. Which pins have to be used?Thanks a...
View ArticleCC1310: Guestion about CC1310 discrete PA
Part Number:CC1310In SWRA490,I know this design is for a frequency range of 470 MHz to 510 MHz, and it mentioned that "If a different frequency than 470 – 510 MHz or higher output power (> 22 dBm)...
View ArticleUCC28780: UCC28780
Part Number:UCC28780Hi Team,Customer is designing a active clamp flyback design with UCC28780. Could you please let me know the right software to run "UCC28780_TRAN_Si.sxsch"? Any user guide for...
View ArticleClik here to view.
BQ28Z610: How to choose the Fuse such as sluube3 circuit?
Part Number:BQ28Z610The customer uses the BQ28Z610 as a protection circuit on the charger schematic. And refer to the circuit diagram of sluube3, how to choose fuse (such as the EVM_sluube3 schematic...
View ArticleClik here to view.
CCS/TMS320F28335: JTAG programming error
Part Number:TMS320F28335Tool/software: Code Composer StudioHi, i am working in my TMS320F28335 test board. During debugging CCS shows"C28xx: Error connecting to the target: (Error -1155 @ 0x0) Device...
View ArticleTXB0304: TXBN0304
Part Number:TXB03041. The waveform after the TXBN0304 is failed.2. It seems the driver level is too low for this circuit.3. PCLK_1 is PCM_CLK and the frequency is 2MHz.4. TXBN0304 output is connected...
View ArticleMSP432E401Y: Errata GPIO#9 relevant for CAN1
Part Number:MSP432E401YMy customer wants to use PB0/PB1 as CAN interface (they need two...).Is the errata GPIO#9 relevant for this config? Can both CAN interfaces be used as usual?Best regards,Frank
View ArticleCCS/CC2640: Cannot update fw to CC264BPA-S(cc2640) with CCS 8.3.0
Part Number:CC2640Tool/software: Code Composer StudioHi AllI can update fw on LANCHXL CC2640R2 EVM board with CCS8.3.0But when i connect GND,RESET,TMS,TCK,3V3 to CC264BPA-S module which mounted on my...
View ArticleClik here to view.
BQ25713: About REGN voltage
Part Number:BQ25713Hi,Could you tell me the voltage value of REGN in each mode.I want to know the VREG voltage corresponding to each mode and VBUS voltage.・Buck mode・Boost mode・Buck boost mode・Battery...
View ArticleDLP3010EVM-LC: Trouble communicating with DLP3010EVM-LC , return device busy,...
Part Number:DLP3010EVM-LCHiI checked the forum for communicate with DLP3010EVM-LC with cypress chip and its usbserialexample code.I found that it should pull up GPIO5 first and wait for GPIO6 to pull...
View ArticleCC2640R2F: Sensor Controller Studio assembly workflow
Part Number:CC2640R2FHi,I am implementing some timing-critical functions on the Sensor Controller which need to be coded in assembly. I have managed to integrate this in the C Execution Code by...
View ArticleADS1292R: ADS1292R Heart rate not getting HR values beyond 110 BPM
Part Number:ADS1292RDear Sir,Greeting of the day..!!We are facing the issue in HR value. Kindly go through the below scenario and suggest a suitable solution for this.We are interfacing ADS1292R...
View ArticleClik here to view.
CCS/TMS320F28069: Ask for document about CCS GUI composer-designer
Part Number:TMS320F28069Tool/software: Code Composer StudioHello,Besides of the online user guide, do we any more document about GUI composer V2?My customer have difficulty to see the curve of...
View Article