Clik here to view.
AWR1642BOOST: Print velocity info in ROS for AWR1843BOOST
Part Number:AWR1642BOOSTI'm using aAWWR1843BOOST EVM device with mmwave sdk 3.1I'm trying to print the velocity, x, y, z coordinates and intensity for every point detected.When i tried to use the...
View ArticleTSM102: TSM102 high/low voltage output levels
Part Number:TSM102The TSM102 datasheet shows the typical output voltage level when the Vcc rail is at +30V. Is there any data or charts as to what the output levels are when powered with +5V?
View ArticleClik here to view.
LM96080: Question about the Logical "0" output voltage of open drain output
Part Number:LM96080Hi team, When customer evaluates LM96080 device, they found the Logical "0" output voltage of open drain output only has the min value (0.4V) as below. Usually Logical "0" output...
View ArticleClik here to view.
TMS570LS1224: TMS570LS1224 launchpad + CAN Transceiver problem fix.
Part Number:TMS570LS1224Dear all: Just Information not question. Develop TMS570 CAN communication. the cheap solution is buy lanchpad and CAN Transceiver from Taobao. But during...
View ArticleClik here to view.
CCS/TMS570LS0714: TMS570 MCAL EB tresos configuration question
Part Number:TMS570LS0714Tool/software: Code Composer StudioHII have a problem. Please see the following configuration pictures. Is there any mistake in my configuration?I now want to configure the...
View ArticleEVM430-FR6047: EVM430-FR6043: Is it possible for TI to share the TINA...
Part Number:EVM430-FR6047Hello,I recently found a simulation model for TIDA - 01486 Analog front end for EVM430-FR6047 board. Is there any Simulation model available for users for the analog front end...
View ArticleVSP5610: Interfacing with FPGA Basys 3 board
Part Number:VSP5610Do you provide support for interfacing the ADC sensor with FPGA basys 3 board, it would be great if you can provide me VHDL code for interfacing with the ADC sensor, any series of...
View ArticleINA188: INA188 Input Stage Offset Voltage Test Condition
Part Number:INA188Dear Sir,I have a question on the subject INA188 test condition. What is gain? Is it G=1 or G=100?I refer to INA828. It specifies G=100 for test condition of Vosi. I suppose higher...
View ArticleClik here to view.
AMC1301: TIDA-01513, calculating equation issue
Part Number:AMC1301HiI have a question about AMC1301-Q1. I saw the Page 6 and 11 of the reference design TIDA-01513 tells the detection principle and final verification result. It confused me if the...
View ArticleDLPDLCR3010EVM-G2: How to use external trigger to synchronize the projector...
Part Number:DLPDLCR3010EVM-G2Hi all,I want to know how to use the external trigger to synchronize projector and camera in LCR3010EVM-G2.Because I didn't see any useful information in the user's manual...
View ArticleTINA/Spice/UCC28019A: ucc28019a
Part Number:UCC28019ATool/software:TINA-TI or Spice Modelscan i add an ic (ucc28019a) for simulation?if yes?, how can i do it?
View ArticlePower module for 3.3V and 5V output which could meet IEC60601 medical...
Hi TI,Does it have any recommend power module for 3V3 and 5V output. Output current rating is 6A to 8A for 5V output.Output current rating is ~ 1A for 3V3 output.Input voltage is 12V. For medical...
View ArticleLinux/TDA2: PCI configuration for TDA2x
Part Number:TDA2Tool/software: LinuxHi,I want to know about how the PCI lines of TDA2x can be configured in linux? I have a custom board developed based on TDA2x. I have to configure PCI as two 1X1 pci...
View ArticleLM3488: LM3488
Part Number:LM3488Hello;We are redesigning a design with a LM3488MM/NOPB in it. Can you tell me something about its product longevity?Thanks in advance;Regards;Pieter
View ArticlePMP30464: LM5119 for DC/DC printer power design
Part Number:PMP30464Dear SirGood day! There are DC-DC power requirement for printer power and need IEC60950 LPS(Limit power source) . Spec as below.1.Vin: 12-48V Vout: 8.3V/5A OCP :6.5A arround...
View ArticleTIDM-HV-1PH-DCAC: TIDM-HV-1PH-DCAC
Part Number:TIDM-HV-1PH-DCACHiI wanted to run this inverter with F28049c board. Can you help me with source code or the changes I need to do in F28377 code.Regards,Ramesh
View ArticleCCS/UCD3138: how much is value of the capacitance betweent GND with...
Part Number:UCD3138Tool/software: Code Composer StudioHello I want to know how much the value of the capacitance is betweent GND with Fault1,Fault2 Pin in UCD3138 ?or how much the value of the...
View ArticleAM3359: Requirement added for Power-Supply Sequencing
Part Number:AM3359The requirement was added to footnotes of each from Figure 6-2 to Figure 6-6 on the datasheet which is changed from SPRS717J to SPRS717K."If all the 1.8-V supplies are not sourced...
View ArticleADS1242: ADS1242
Part Number:ADS1242Hello;We are redesigning a design with a ADS1242IPWT in it. Can you tell me something about its product longevity?Thanks in advance;Regards;Pieter
View ArticleRTOS/LAUNCHXL-CC1352R1: Frequency Hopping Mode
Part Number:LAUNCHXL-CC1352R1Tool/software: TI-RTOSHi All,I am working on CC1352R launchpad in TI15.4 stack (SUB 1 GHz) and CC13x2_sdk_2_20_00_71 version. In this I am working with example code of...
View Article