Clik here to view.
TMS320F28377D: ECAP Synchronisation
Part Number:TMS320F28377DHi,I want to synchronize ECAP1-ECAP4 to same TBCTR(time base counter).I have followed the below discussion to get my ECAP's working in a synchronization to get the phase...
View ArticleDS80PCI402: Use two DS80PCI402 as GEN3 PCIE x8
Part Number:DS80PCI402Hi Team, Customer want to use two DS80PCI402 as GEN3 PCIE x8, whether is this proposal available? if so, what parts should be taken care? if possible, could you please help to...
View ArticleTPS65982: USB traces length on PCB to Type- C connector are over 6000 mil
Part Number:TPS65982Does TI have concern on USB traces( pins K6, L6, K7 and L7) length on PCB to Type- C connector are over 6000 mil ? Thanks!(Please visit the site to view this file)
View ArticleTPS54160: Frequency Compensation Component Selection
Part Number:TPS54160Hi,I am Using TPS54160 Ic for Vout= 5V , Input voltage is = 24V and outptu current = 1AI have simulated the design in WEBENCH and working good. but i want to calculate manually the...
View ArticleDRV10987: Phase resistance & Phase to Phase Kt settings
Part Number:DRV10987Hello TI Community,I have a BLDC motor whose parameters are typically as following :Phase resistance = 1.44Ohms (tolerances ==> R = Min. 2.59 Ohm / Max. 3.17 Ohm)Phase to Phase...
View ArticleClik here to view.
CCS/TMS320F28379D: CCS8
Part Number:TMS320F28379DTool/software: Code Composer StudioI get errors when building my project. this code was generated in matlab 2018b for TMS320F28379D. Please help me to resolve this error.
View ArticleCC1352P: LAUNCHXL-CC1352P-2 Design Files Altium format
Part Number:CC1352PHello All,We start to make a Pcb based on CC1352P.We have already download the Zip file of the reference design LAUNCHXL-CC1352P-2 Design FilesUnfortunately , it contains the PCB in...
View ArticleTMS320F28335: Time to erase the Flash memory
Part Number:TMS320F28335Hello,What is the approximative time to erase 32K sector of the flash memory?In the SPRS439F of june 2007 (rev april 2009), this time is specfied around 11sec. in the same spec,...
View ArticleTM4C1231E6PM: High output level aleatory drop
Part Number:TM4C1231E6PMDear SirsThe PB6 of TM4C1231E6PM is configured as output. The pin is driving mosfet BSS138 that tuns on/off a relay.ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);...
View ArticleTMS470MF06607: Need some Reference schematic for this controller
Part Number:TMS470MF06607Hi,I would like to use TMS470MF06607 Microcontroller for one of my application.I need some reference designs and schematic for this controller to interface can transceiver.we...
View ArticleLinux/TDA2PXEVM: D3 IMX390 Camear frame-rate
Part Number:TDA2PXEVMTool/software: LinuxI am using D3 IMX390 camera and vskd 3.05 version on "TDA2PX Fusion kit.The problem is that the frame rate of the camera is only about 22 ~ 23fps.I need a...
View ArticleClik here to view.
TXS0102: used for signal improve: increase rising edge and falling edge
Part Number:TXS0102Hello,Can i use TXS0102 to increase the rising edge and falling edge of 2 SPI signal (data rate 1Mbps)? Voltage translator is not needed, from 3.3V to 3.3V. Here is captured waveform...
View ArticleClik here to view.
OPA333: Output Regulation delayed by input Saturation, is there a recovery...
Part Number:OPA333Hello dear Developers,I am using an OPA333 as a non inverting Amplifier with Gain of ~100 3.3V Single Supply. Both Inputs are Protected by BAT54S.The voltage on the positive input...
View ArticleCCS/TUSB8041: Overcurrent event behavior
Part Number:TUSB8041Tool/software: Code Composer StudioHello, I want to realize the following configuration in TUSB8041 When one of 4 downstream ports has overcurrent event, I want to disable only the...
View ArticleAM3358: UART pins don't work with PRU
Part Number:AM3358Hi,I have succesfully managed to run a simple application on PRU, which turns on and off some GPIO outputs.Now I wanted to try the "PRU_Hardware_UART" example, but when measuring the...
View ArticleTFP410: Questions for LV-TTL RGB to HDMI bridge
Part Number:TFP410Hi team,The customer is considering building some prototypes of the LV-TTL RGB to HDMI bridge board with TFP410.(1) Is I2C setting needed for the TFP410 operation? Can the customer...
View ArticleClik here to view.
CCS/AWR1642: can not receive the correct message from uart port
Part Number:AWR1642Tool/software: Code Composer StudioHi,when I connected the EVM with pc(ubuntu),I sent 'advFrameCfg\n' to uartport and I can't receive the correct command 'Done'.It just returned...
View ArticleOPA1622: Connecting OUT to GND to discharge of output pin during disable
Part Number:OPA1622Hi allWould you mind we ask OPA1622?Is it possible to connect OUT to GND to discharge of output pin during disable?We assume that it must proceed the sequence as follows;1. Disable...
View ArticleRTOS/CC1352P: Working only with the PIN interface
Part Number:CC1352PTool/software: TI-RTOSHi,Following previous conversation, I concluded that the PIN interface is a more advanced GPIO interface version, giving more capabilities and flexibility to...
View ArticleBQ25713: BATDRV voltage range and P-MOSFET maximum VGS
Part Number:BQ25713Hello,I am following the EVM to make my design. Thus I used CSD25402Q3A as the BATFET. But in my desing VSYS is 12V nominal (10V-15V range) and the VGS range of this FET is +/-12V....
View Article
