CC2630: RESET pin voltage threshold and POR threshold
Part Number:CC2630I am going in detail through the CC2630 datasheet in search for the RESET_N pin voltage threshold and for the POR threshold and I am unable to find them.I can successfully identify...
View ArticleADS1299-6: CLKSEL pin connected to GPIO
Part Number:ADS1299-6Hi, is it valid to connect the CLKSEL Pin to GPIO1 so that the clock selection can be controlled. Can the ADS switch clocks after boot or does it have to be during boot?Does CLKSEL...
View ArticleTMS320F28377D: Incorrect measured value on ADCINB0
Part Number:TMS320F28377DHi,We are undergoing an issue on ADCINB0 pin of our TMS320F28377D.The voltage value measured on the board is equal to 1.156V but the result of our acquisition outputs 1.204V...
View ArticleUCD90160: Bias Current at PMBUS_ADDR0 and PMBUS_ADDR1
Part Number:UCD90160Hello TI Tech support. We are having issue with the UCD90160. It seems like the Bias current is off while the device is reading the voltage at Addr0 and Addr1 to set the I2C...
View ArticleTPS23880: The sensing resistor
Part Number:TPS23880Hi,According to datasheet and EVM suggest that using 0.255Ohm as sensing resistor. Customer is wonder to know that is there any document that discribe how this value comes from and...
View ArticleClik here to view.
LM43603: LM43603 Circuit - Critical Issue in Board Bringup
Part Number:LM43603Hello,I am working to bring up one of my boards which has the LM43603 regulator as the primary voltage regulator.I am facing a vague and critical issue with LM43603 circuit, which is...
View ArticleTPS23880: Ths Sifos testing
Part Number:TPS23880Hi,May I know if TPS23880 have already passed Sifos testing or not?If yes, could TI provide testing report or related document?If not, how I convince customer that TPS23880 will...
View ArticleMSP-FET: What's max output current on pin 2?
Part Number:MSP-FETHi Team,May I know the max output current of MSP-FET pin 2(VCC-TOOL)? Thanks.Best regards,Penny
View ArticleClik here to view.
TPS65100: TPS65100 VCOM voltage setting equation
Part Number:TPS65100Hi,Could you tell me the correct way to set the VCOM voltage on the TPS65100? The datasheet and evaluation kit and set the output voltage at half of Vo1 with equal value feedback...
View ArticleCC1310: Sensor/Collector: Orphan but still not quite so orphan
Part Number:CC1310Hi,If a sensor is put into orphan state due to handleMaxDataFail() call, and the sensor later receives a config request from collector, the sensor will respond with a config...
View ArticleBQ51050B: bq51050BEVM-764 WPC Compliance Failure
Part Number:BQ51050BThe q51050BEVM-764 data sheet claims WPC Compliance. When we test compliance using a CATS2 system (NOK9) the EVM out of the box fails test Part 3: Req #57. The received power minus...
View ArticleTMS570LS0714: Sampling rate and acquisition of the 12 bit SAR ADC in TMS570...
Part Number:TMS570LS0714I'm using TMS570LS0714 for my design and as i was going through the ADC parameters in the datasheet i couldn't get the acquisition time and sampling rate values. Or i'm not sure...
View ArticleMSP430F479: UART data not correct
Part Number:MSP430F479Hi,I am trying to send one byte of data over the UART at a baud rate of 115200 Hz. I am using the BM70 ble module to transfer the data and the baud rate of the BM70 module is also...
View ArticleTAS5421-Q1: Class D amplifiers
Part Number:TAS5421-Q1How do I unsubscribe from the audio forum.
View ArticleDP83822I: DP83822 strap pin configure for work with ET1100
Part Number:DP83822IDear team,Do you have a guidance notes of DP83822 regards to strap pin configuration for make it work with BECKOFF ET1100? Thanks!Regards,Alex
View ArticleCC3220MOD: How much speed can it reach when I choose SD host mode
Part Number:CC3220MODDear TI Experts,I find that CC3220MOD's SD Host has these three pins: CLK，CMD, DATA0,How much speed can it reach when I choose SD host mode and connect CLK CMD DATA0？Can it support...
View ArticleCDC3RL02: Can I tie VLDO to an external 1.8V supply?
Part Number:CDC3RL02We made a mistake and tied the clock request lines to VLDO thinking it was always on. Now I see you're not supposed to do that. Is it possible to power VLDO from an external 1.8V...
View ArticleADS1299: Referential montage input filters
Part Number:ADS1299I am reading section 10.2.2 of the ADS1299 datasheet, and I am not sure what size components to use when designing a circuit for a referential montage. If the input impedance needs...
View ArticleClik here to view.
TAS5755M: Asking for the TAS5755 0x51 and 0x52 setting
Part Number:TAS5755MHi Team,TAS5755 0x51 and 0x52 has three mixer each. The GUI can set the max value is 15.9.Does this mean 15.9dB on each input? And this mixer can be used for gain increasing if...
View ArticleCCS/CC3220: Massive Delays in HTTP or SNTP requests using slnetutils
Part Number:CC3220Tool/software: Code Composer StudioHi, Note: All my times are measured against the windows clock so not terribly accurate...So the titles says it all. I've tried using the...
View Article