OPT3002: Optical Center of the OPT3002 Sensor, P L E A S E...
Part Number:OPT3002Hi Folks,During my Design process I tried to find the Optical Center Point of the OPT3002.The reason for my question is related to the two row array of mini sensors that have a...
View ArticleAFE7686: AFE7686 direct connection to 66AK2K2L device
Part Number:AFE7686Can I interface the AFE7686 directly to the 66AK2K2L chip using just 2 JESD204 lanes for xmit and rcv? Also, can I operate the AFE7686 ADC in the second nyquist zone (subsampling...
View ArticleClik here to view.
TMS320F28379D: ADC Results clipping at specific integer value + ADC signal bleed
Part Number:TMS320F28379DGreetings,I'm using the F28379D Launchpad to do some testing right now. I've initialized ADC A and ADC C to 16-bit differential modes. According to the launchpad data sheet,...
View ArticleADS1281: ADS1281 questions (data rate, pipelining, 24-bit output)
Part Number:ADS1281I have a few questions about the ADS1281 Analog to digital converter:Table 5 specifically says the rates provided are for a 4.096 MHz clock. Table 6 doesn't explicitly state that....
View ArticleTVB1440: 7680*4320@30Hz support?
Part Number:TVB1440Hi Team,Can TVB1440 support 8k (7680*4320@30Hz)? If not, are there any suitable redriver? Also, would TVB1440 limit the resolution of Hsync/Vsync?Thanks
View ArticleClik here to view.
CC2530: ZigBee Module (WE1005)
Part Number:CC2530Hi I'm working on application that require an RF zigbee module I bought ZigBee Module (WE1005) it's based on CC2530 manufactured by RF star.I want to integrate the module with CC3200...
View ArticleIWR1443BOOST: Need help using the DCA1000EVM with IWR1443Boost where the...
Part Number:IWR1443BOOSTWe would like to use the IWR1443Boost EVM connected to the DCA1000EVM, where the 1D-FFT is performed in the IWR1443's HWA. So range data instead of raw ADC data would be...
View ArticleClik here to view.
Xilinx KCU105 with HSDC Pro - Error
HiI am trying to use the KCU105 with the ADC32RF45EVM and am following all the steps mentioned in the user guide. I keep getting the following error and am not able to connect to get the setup working....
View ArticleOMAP-L138: WDT Enable / interrupt driven?
Part Number:OMAP-L138Hello,I am setting up the watchdog timer and, also, setting an interrupt on Timer 1, so when the WDT counter expires, I can execute some things before the device is reset. But, my...
View ArticleCCS/LAUNCHXL-F28379D: CAN on CPU2
Part Number:LAUNCHXL-F28379DTool/software: Code Composer StudioI'm trying to run the CANB module from CPU2 on a LaunchPad XL. I've modified the IPC example to include CAN setup and modified a CAN...
View ArticleBQ28Z610: Different readings for Cell 2 voltage and BAT pin voltage
Part Number:BQ28Z610Hi, I'm looking at a battery that was supposedly charged at least once after production. My cell 2 voltage is reading 0mV (via BQ Studio) but the BAT pin voltage is reading 3536mV....
View ArticleClik here to view.
TMS320C6747: OSCIN level translation
Part Number:TMS320C6747Hey folks,I spend most of my time with audio circuits, so DSP is relatively new to me, but I'm modifying an existing circuit here, planning to replace this passive crystal...
View ArticleTPA3118D2: Are Intermediate gain settings for TPA3118D2 possible?
Part Number:TPA3118D2Hi, in the TPA3118D2 datasheet, Table 1 - Gain and Master or Slave, it defines R1 and R2 resistor values for setting the gain to 20, 26, 32, and 36 dB.The text above the tables...
View ArticleClik here to view.
BQ25700A: Need some support for their software team in understanding in how...
Part Number:BQ25700AHello team,Hope you are doing well. When you get a chance can you help with how to interface with BQ25700A via SMbus. Customer is following below steps:1. You can leverage IO Space...
View ArticleCC2564: Updating Bluetopia Demos to Support CC2564C (Evaluation Module)
Part Number:CC2564I have the MSP-EXP430F5438 Evaluation Board along with the CC2564C dual mode evaluation module.I've downloaded and installed the Bluetooth Evaluation Software...
View ArticleTINA/Spice/LMP8481: Missing LMP8481 PSpice model
Part Number:LMP8481Tool/software:TINA-TI or Spice ModelsFrom DigiKey website "... digikey.com/product-detail/en/texas-instruments ... LMP8481ASQDGKRQ1/296-46592-1-ND/7062569" I downloaded the...
View ArticleINA302: Evaluation Module CAD files
Part Number:INA302Hello,I plan to use the INA302 in my next design.are the CAD files used for the evaluation module available? I think it was done in Altium. That would be very helpful.Regards,Pere
View ArticleDLPNIRNANOEVM: Effect of ambient / detector temperature on the absorption data
Part Number:DLPNIRNANOEVMI am trying to use this (DLPNIRNANOEVM) sensor in an environment where temperature varies - in a manufacturing environment. I have several questions pertaining to the effect of...
View ArticleMAX3232: what voltage caps to use
Part Number:MAX3232Team, please provide some guidance to my customer's question:I am looking at adding a TI MAX3232 to my design. It requires external caps for the charge pump, denoted as C1 – C4 in...
View Article