Input Edge Count Individual Up or Down mode not working in CC2538 using Timer?
Hello All,Looking for a quick feedback.I am giving a rising edge frequency to CC2538 at BSP_LED_1 pin of CC2538. I would like to measure a frequency from 500 Khz to 1 MHz. of 50% duty cycle.I would...
View ArticleMeasuring the delay between the different components in ezsdk
Hello TI,We are using DM8148 based custom board. We have made a custom application in ezsdk_dm814x-evm_5_05_01_04 using the capture_encode and audio_encode demos. We want to measure the time consumed...
View ArticleCan we connect YUV sensor[gives output YUV-4:2:2] to parallel video port(VIP)...
Hi All,I want to know is it possible to connect a YUV sensor [output format - 4:2:2 YUV], to parallel video input port (VIP) of ISS, on DM8127?We have connected Data lines D0:D7 from sensor, to...
View ArticleTivaWare usb-dev-serial -example is not working
Hello,Any ideas how can I get the TivaWare usb-dev-serial -example to work with Tiva Launchpad? The example compiles and can be flashed but when I put the usb-plug to non-debug usb-socket Windows won't...
View Articleqt install error
Hello,I try to install qt 4.8.1 on ubuntu 10.04 32bit, according to TI application note used with DM816x.(Please visit the site to view this file)the make command was done OK with no errors/warnings,...
View ArticleOMX_EventError: 0x80001005
Hi Team,Please give me some suggestions to resolve this. Currently i am writing some test codes for video mixing. After mixing two videos im using omx_h264enc to encode the output of the videomixer....
View ArticleMULTIPLE ADC'S
Hello, I am using MSP430G2553 launchpad. I need to use 2 ADC 's for my project, i doubt in how to access the conversion values of my two inputs.For example, i am choosing INCH_2 in ADC10CTL1...
View ArticleClik here to view.
communication between 2 uart (USCIA0 and USCIA1) of msp430F5529 launchpad
Hello, I'm very new to MSP430F5529 launchpad. I want to communicate between 2 devices and computer (hyperterminal). but right now I'm trying to communicate between 2 uart by using...
View ArticleCan we use Anaren A2530E24C chip as RF proprietary mode?
Hi, Can we use A2530E24C chip in RF proprietary mode preloaded with Anaren’s AIR-ZNP inbuilt stack , if it is possible then suggest steps how to use chip for RF...
View ArticleCC3200 Serverpack Unstable
Hi All,I found a problem about CC3200 serverpack, if you do a smartconfig operation failed, please update it again, Maybe you can be successful.So i think the serverpack is not stable enough.
View ArticleClik here to view.
CC3200 Module Authentication
Hi All,I designed a CC3200 Module and it can work well.And it has been mass production.I have a question about the WIFI authentication of my CC3200 module.How do I authenticate it?Who can give me the...
View ArticleFully differential amplifier with single supply but differential input
Hi there,I just tumbled over a bunch of application note, which where really helpfull but didn't really answered my question. Here it comes: I have an audio codec which outputs a differential analog...
View ArticleAlternate ways of programming the CC3200 device (other than UniFlash).
Hello,I am working with CC3200 LaunchXL device.What are the alternate ways of programming the CC3200 device, other than using UniFlash ??Also, what are alternate ways of flashing files in the Serial...
View ArticleWhat does the input offset voltage mean
Hi everybody,sorry that I have to ask t his, but I just couldn't find any answer for this question. My problem with the value of the "Input offset voltage" in all the OPA datasheets is that I can't...
View ArticleSRC4392: I2C strange behaviour
Hi,I'm using the SRC4392 on a custom board, with an I2C Clock on 100kHz. On that bus, there are more devices which all work perfectly.When I want to address the SRC4392 (address is 0x70), I use the...
View ArticleProduct differences advice
Hi all,I want to ask what are differences in quality between this...
View ArticleProper suffix describing Byte Sizes.
Things are getting a bit confused when it is proper to add the suffix (KB) to a decimal string describing a memory block, file, sector, packet or partition.Single Blocks should be described in BYTES...
View ArticlePurepath wireless configurator
We are using "purepath wireless configuator 1.4.2.38775" to configure the CC8530 with the "DSP (Generic digital audio device - no restriction)" device.The "IO mapping" matrix shows an error between...
View ArticleHeap Size for CCSv6 Delfino F28377D
Hi e2e,Does anyone know the max heap size for CCSv6? From trial and error it appears to me that it can only be 4096, but with the amount of calloc commands I am using this is not enough. Does anyone...
View ArticleClik here to view.
TM4C1231C3PM GPIO
Hi allMCU: TM4C1231C3PM KEIL: keil5.0I now want to use PB[3：2] as GPIO Function，but the table above shows the default state is not GPIO function.How should I configure them?ThanksLewis
View Article