Clik here to view.
CC2640R2F: IAR/CC2640R2F: How do I copy a simplelink_cc2640r2_sdk examples to...
Part Number:CC2640R2FHi, I'm studying CC2640R2-LAUNCHPAD using IAR Embedded Workbench Software.I installed simplelink_cc2640r2_sdk_1_50_00_58 and done just the examples included.But, I want to copy the...
View ArticleUSB2ANY: Command line interface required to control connected I2C devices
Part Number:USB2ANYhello,Using USB2ANY (HPA665) hardware to control some I2C devices via I2C messages sent .PC<-------usb cable-->USB2ANY<-----i2c lines--->DUT(device under test).Is there a...
View ArticleTAS5707: Is it advisable to use TAS5707 in one channel mono mode?
Part Number:TAS5707Hi,My customer is exploring to use TAS5707 in mono mode using only one of the available channel. However, we aren't sure if this configuration may induce any issue since the device...
View ArticleOPA1612: The lowest resistance that the OPA1612 opamp can drive while...
Part Number:OPA1612My customer is designing an amplifier stage to interface between a measurement amplifier (B&K 2636) and a computer audio interface. The output of the 2636 is typically...
View ArticleClik here to view.
RTOS/CC2640R2F: SENDING Custom Message Via ICALL Message
Part Number:CC2640R2FTool/software:TI-RTOSHi,Am working on Repeater code using CC2640R2F. Now i can send the repeater packets. But while adding Heartbeat in to the task my code behave abnormally. There...
View ArticleClik here to view.
RTOS/SIMPLELINK-CC13X0-SDK: RTOS/SIMPLELINK-CC13X0-SDK,
Part Number:SIMPLELINK-CC13X0-SDKTool/software:TI-RTOShow to extract the value of the temperature in a thread in order to send it in RF, knowing that I recover this value during a debug as shown in the...
View ArticleWEBENCH® Tools: what does temp in webench mean?
Tool/software: WEBENCH® Design ToolsHi,I have a quite simple question i think. but i dont know the answer so I ask here...In webbanch power designer there is writen "temp (deg)". what does this refer...
View ArticleTUSB2046B: connect with USB2.0 Host
Part Number:TUSB2046BHi Sir If I connect upstream to USB2.0 host (high speed) ,the downstream port will work on USB full speed mode ,is it right ?
View ArticleUCC28950: Excel Design Tool in case of Adaptive delays approach
Part Number:UCC28950Dear e2e support,My customer is working on our full bridge controller and would like to set it in Adaptive Delays instead of Fixed Delay mode (connecting the ADEL and ADELEF...
View ArticleOMAP-L137: Syncing ADC and DSP when both units are isolated from each other
Hello,I'm having a bit of trouble syncing the ADC and the DSP. The DSP is on the non-isolated side of the board and the ADC is on the isolated side of the board. The sides are separated by digital...
View ArticleTPS74801: Max Cout calue of TPS74801
Part Number:TPS74801HiMy customer use TPS74801 with Cout of max 150uF.But this device is not written about max Cout value in datasheet.Can this device use Cout of 150uF?Best regards,Yokota
View ArticleCCS: C5505 Programming PCB standalone
Tool/software: Code Composer StudioHi, I'm try to make my project persistent on a self-made SoC based on C5505 PCB.I Use programmer.out that I used with c5505 eZdsp demo board (programmer.out)When I...
View ArticleLinux/PROCESSOR-SDK-AM335X: MMC0_CD as GPIO
Part Number:PROCESSOR-SDK-AM335XTool/software: LinuxHi,Is there any way to use the MMC0_CD pin as a normal GPIO for my application.I am using SD card but I dont need the MMC_CD functionality.I just...
View ArticleTPS3808G01DBVEVM: TPS3808 #RESET output delay erratic
Part Number:TPS3808G01DBVEVMHello,Using the TPS3808G01DBVR, we have the #RESET output pin 1 pulled up to +3.3V through a 1k resistor. VDD pin 6 and SENSE pin 5 are tied to a +2.5V supply that comes up...
View ArticleClik here to view.
CC2640R2F: power consumption optimization
Part Number:CC2640R2FHi guys,We are working on CC2640R2 device for an ultra low power application. The image below is our power consumption measurement after disabling all the modules. Right now there...
View ArticleTS3USB221: height
Part Number:TS3USB221Hi Sir Do we have 5Vcc and 0.35mm height solution is similar with TS3USB221?Thanks
View ArticleClik here to view.
CCS/CC2650MODA: Unable to build ble5_simple_broadcaster project
Part Number:CC2650MODATool/software: Code Composer StudioHello,I've imported the projects:ble5_simple_broadcaster_cc26x2r1lp_app which also automatically imported the...
View ArticleLAUNCHXL-CC1350: TM4C1294 USB converter f/w needed
Part Number:LAUNCHXL-CC1350Is the TM4C1294 USB converter F/W available on the Launchpad board so that the board can be copied?
View ArticleClik here to view.
J6EVM5777: How to flash MLO and u-boot binaries on QSPI memory through UART3...
Part Number:J6EVM5777Hello All,We are trying to flash MLO and u-boot.img binaries on QSPI through UART3 mode on our custom board which is based on DRA7xx chipset.On below link, it is mentioned about...
View Article