Question about TS5A3159-Q1 OFF leakage current spec
Hi,Does anyone have the distribution data of the TS5A3159-Q1 NC/NO OFF leakage current spec?ThanksGo
View ArticleIssue with Ethercat on am3358- Beagleone black
Hello Sir,I want to implement Ethercat stack on beaglbone black (am3358) to drive a Kollmorgen AKD servo drive. I am using TI SDK kit 7 with linux kernel 3.12. I checked the data sheet of am3358 and...
View ArticleOMAP4460 4AJ.1.1 with 2GB RAM
Hi,We already porting 4AJ.1.1 on 1GB device and it is working fine.And we got a new HW with 2GB RAM and it's work with 1GB code.So I change some code in u-boot and x-loaderx-loader:...
View ArticleAM335x Production Programming
This seems to be a common question but I have not been able to find a complete answer.What is the preferred method for flash programming in a production environment?The wiki mentions a method, but says...
View ArticleRGB output using VFDC
Hi,is there any examples on how to configure VFDC component to utilize RGB instead of YUV signals. Is this supported? Thanks,Danillo
View ArticleClik here to view.
DAC8831EVM: help with strange noise
I am trying to use the DAC8831, and made a PCB based on the DAC8831EVM schematic. To test it, I supplied +/-5V and looked at the ouptut, which should be the result of the power-on reset. However, I...
View ArticleTimer and GPIO interrupts
First, what I'm trying to do. I need a CC2541 to measure the pulse width of a train of pulses and load those into a buffer, but I don't know when those pulses will begin. In the CC253x/4x User's Guide,...
View ArticleQuestion of LM94022 certification
Hello,I have a question from customer.>Audio product : AV-Receiver>Used Ti part : LM94022BIMG/NOPB>Question :How about information certification of LM94022?Customer heard LM94022 is available...
View ArticleHigh Resolution Timer to Monitor Fluctuations in Period
Hi,I have an application where I need to time the duration between two events. The events do not necessarly fall on the same period every time (i.e. exectution time during the events can vary). The...
View ArticleWhat TI Cortex M3 MCU product is closest to that embedded in the CC2538?
The reason for the question is to determine whether there is a TI, MCU available that is sufficiently close to that implemented in the CC2538 to make direct use of the CC2538DK Contiki port, less radio...
View ArticleHow to create CC3200 project based on one of the example projects?
I'm still attempting to work through the CC3200 Getting Started Guide and hopefully after uninstalling and re-installing CCSv6 from scratch (yet again), I might be able to build the wlan_station...
View ArticleCc3200 GPIO interrupt example code
Dear Sir,i have installed Cc3200 SDK 1.0 and found many example code, now I want to implement a GPIO ISR into "Out of Box" code, objective is drive cc3200 entry smart configuration mode by a GPIO, but...
View ArticleIPC global variable share problem on DSP6678
I find a IPC example project . in the project core0 triger ipc interrupt to core1.and core1 trogers ipc interrupt to core2,and so on.i have no EVM board and this project is run under simulator mode.I...
View Articleethernet - low power mode
Hello,What is the method for moving ethernet into low power ? Is it a matter of changing the power domain (register) ?Thanks,Ran
View ArticleIs it possible to parallel two buck/boost convertors from different sources?
I'm a bit of a newbie to convertors so this might be a daft question.I have two different unregulated but rectified voltage sources (permanent magnet generators) 3 to 20+ vdc and I would like to tie...
View ArticleDisconnect after absence
I would like to disconnect with the mobile device when nothing happens for 30s. After the device is disconnected it should start advertising again. I know there is the GAPRole_TerminateConnection();...
View ArticleClik here to view.
Optimization cycle in BQ34Z110 ; VOK flag not set
Hi all,We are using BQ34Z110 fuel gauge in one of our designs to operate with a 12V 7AH lead acid battery. We have completed the configuration,calibration part & now want to run a optimization...
View ArticleADC not working
Dear Friends,I'm a newbie to C2000 MCU's, as I'm trying to run the adc peripheral, I tried to use the sample code on Controlsuit, but when I connect my signal generator (10H sin wave, 1V pk-pk) to...
View ArticleClik here to view.
SWI and HWI C function calltree problem
Hi All, I am new to use TI-RTOS. I have a bit confusion about HWI, SWI and TASK. Because I have some experience of using FreeRTOS-like RTOSes, so for the TASK I have no problem to understand it in...
View ArticleImport Energia sketch to CCS limitations (what are they?)
Hi everyone,So i was wondering what are the problems of importing or creating a Energia sketch to CCS. It uses GCC which i also don't know the difference from GCC to the other CCS compiler.I really...
View Article