CCS/CC2652R: Overlapping segments at address 0x57fa8
Part Number:CC2652RTool/software: Code Composer StudioHello,I am trying to load zc_light application on cc2652 launchpad using UNIFLASH , but while loading its throwing error as mentioned...
View ArticleLinux/AM5708: [Bring Up] SD1 CLK does not toggle at all on power up
Part Number:AM5708Tool/software: LinuxMy custom AM5708 board is configured to Option 1 Boot Sequence (SD card, followed by eMMC). On power-up, I expect to see some toggles in the SD1 CLK line, but it...
View ArticleCC2531: Not detected by PC after reflashed with Z-Stack
Part Number:CC2531Hi,I have purchased three CC2531 USB dongles and a CC Debugger. I want to flash these dongles with Z-Stack (to make them behave as ZigBee) to be able to communicate (send and receive...
View ArticleClik here to view.
DLPC300: Cannot connect to DLPC300
Part Number:DLPC300Hello,In Win 7, the TCP-IP settings for the DLCP300 are set to beYou can test these to see they are set OK:But in order to communicate with it, in the GUI (V5.0), we have to set the...
View ArticleCCS/CC2652R: why ccs is so slow during project build.
Part Number:CC2652RTool/software: Code Composer StudioHello,why ccs is so slow during project build? It is taking at least 10 minute to build one project. is there any specific system configuration?
View ArticleCCS/TMS320C6455: I am converting a project from CCS v3.3 to v7.4 and am...
Part Number:TMS320C6455Tool/software: Code Composer StudioI am converting this project and when I build a .cmd file is generated that produces build errors. We believe a .tcf file may be able to help...
View ArticleCCS/MSP430FR5739: Tried to initialize USB FET number 2, but only found 1 USB...
Part Number:MSP430FR5739Tool/software: Code Composer StudioA similar thread was started about 1 year ago but I do not see any resolution. I have the same problem now and we are line down so a quick...
View ArticleCCS/TLV320AIC3206: How to set the sampling rate of the codec
Part Number:TLV320AIC3206Tool/software: Code Composer StudioHi,I'm using c5545 booster pack to implement fir hamming window order 161 bandpass filter. Booster pack came inbuilt with aic3206 audio...
View ArticleTMP422: Can we use TMP422 instead of TMP461?
Part Number:TMP422Hi,We commonly use the TMP461 to interface with devices which only have DXP pulled out. In that case, we would connect DXN to GND. Can the TMP422 support this mode? We can’t tell...
View ArticleDLPC300: RNDIS Driver origin Win 7 and Win 10
Part Number:DLPC300In my computer, when connected DLPC300 automatically loads RNDIS driver by Acer (V1.0.0, 1/13/2010), But since my Win OS is 7 (pro), I can also load MS version of this driver (V...
View ArticleCCS/F28M35H52C: set contents of global variable in same line as declaration
Part Number:F28M35H52CTool/software: Code Composer StudioWhen I do the following the variable is zeroed out when I run the code instead of containing the data that I specified.Uint16 myVar[2] = {1,2};...
View ArticleCC2650: Can CC2650 and CC2630 IC's both run Zigbee applications?
Part Number:CC2650Hi, I'd like to design a simple Zigbee board, like a bare bones CC2650 SensorTag, but the CC2630 seems more dedicated to Zigbee applications. Both the CC2650 and CC2630 datasheets say...
View ArticleBQ2012: PFC Value for 2450mAh NiMH
Part Number:BQ2012We are using NiMH battery gas gauge charger IC BQ2012. We added resistors to select a PFC Value =320mVh. Will this work for both 2300mAh & 2450mAh battery packs (sense resistor is...
View Article66AK2H14: Power Down unused Cores
Part Number:66AK2H14Hello, I understand that the 66AK2H14 ARM+DSP processor has the ability to power down unused cores. I wanted to ask those who have powered down the cores if really did conserve...
View ArticleTPS25200: Can one use the TPS25200 in a negative supply
Part Number:TPS25200Hello TPS25200 gurus!Can the TPS25200 be used in the attached PDF drawing? And if not - what would you recommend. The load current is low, <100mA, but we need to protect both...
View ArticleINA333: Thermistor Signal Conditioning
Part Number:INA333Hi all, I have a general question regarding the signal conditioning of a 10kOhm Bead Thermistor. What is the recommended option for best accuracy to interface to a standard ADC within...
View ArticleBEAGLEBOARD-X15: Changing the Pinmux configuration with the AM5728
Part Number:BEAGLEBOARD-X15My engineering team and I are working with a BeagleBoard-X15 and plan on gathering sensor data through the pins mapped to the SPI and UART pins on the onboard AM5728...
View ArticleCC2650: Connecting Multiple SensorTags with SensorTag app CC1350 and CSV
Part Number:CC2650I have 2 CC1350 SensorTags (BTLE + other wireless option). Am just using BTLE so very similar to CC2650. Product page describes: Max devices = 8.I have the iOS app on an ipad mini,...
View ArticleTRS3122E: Current on VL?
Part Number:TRS3122EI am looking at using the TRS3122E on a 1.8V based logic system so I can avoid additional voltage translators. I will be running the Vcc off of 3.3V. Figure 1 of the datasheet...
View ArticleCC2540: CC2540 USB Dongle Windows 10 x64 Driver
Part Number:CC2540I'm trying to use the CC2540 USB Dongle as a packet sniffer. It was pre-programmed with the corresponding firmware, but I don't manage to install it on my PC and use it as a sniffer...
View Article