Clik here to view.
AWR1443BOOST: BEST SUITED mmwave sensor EVM for Long-range and Mid-Range...
Part Number:AWR1443BOOSTAs the total number of virtual antennas in AWR1642 is 8 and in AWR1443 the number is 12. So, which will be the best suited EVM for Mid-Range and Long- Range applications in...
View ArticleADS8588HIPM GND and timing
Hello team 1. I need double conform with PIN 26 is connect GND or AGND?https://e2echina.ti.com/question_answer/analog/data_converters/f/58/t/129734 2. I am confuse the Timing of the ReadData as...
View ArticleAWR1642: Antenna decoupling algorithm in dss demo
Part Number:AWR1642Hi,In the dss demo, the function MmwDemo_dcRangeSignatureCompensation is introduced to antenna decoupling，I can understand how the function works, but I do not understand the...
View ArticleClik here to view.
CCS/TMS320F28379D: Debug probe error
Part Number:TMS320F28379DTool/software: Code Composer StudioHi: I have a problem in debugging the borad using MCU--TMS320F28379D made by myself. When testing, I tryed some code of TI's example device...
View ArticleTMS320F28377S: driverlib reading periferals registers while debuging
Part Number:TMS320F28377SHi,I'm migrating from the instaspin 28069 HAL to the driverlib 28377S. While debuging a intaspin project you can read the periferals registers value via the HAL structs. Only...
View ArticleAM3354: USB_VBUS cannot reach 5V
Part Number:AM3354Generic question: What can cause USB1-VBUS to rise to 3.3V only? It doesn't rise to 5V, leading to AM3354 disabling (toggling) VBUS.Customer had rectified the schematic mistakes from...
View ArticleOMAP-L138: trouble to access 8-bit NAND flash, 1st byte skipped of any string...
Part Number:OMAP-L138We've designed and build (mostly successfully - everything but the 8-bit NAND works) an OMAP-L138 embedded system, whose processor kernel (CPU, RAM, Flash and Power manager) is an...
View ArticleDP83822I: Under timing requirements for RGMII in the DP8322i data sheet,...
Part Number:DP83822ICustomer is measuring signal integrity / timing on their Ethernet interface where they use the DP83822I PHY.One of these interfaces runs RGMII 100Mbit.Under timing requirements for...
View ArticleCompiler/MSP432P401R: Problem with MultiChannel ADC
Part Number:MSP432P401RTool/software: TI C/C++ CompilerI am trying to read in 2 signals through the ADC pins. Whenever I run the code, only the first ADC pin value is stored. During debugging, I found...
View ArticleCC3220SF-LAUNCHXL: cannot upload code into cc3220sf using uniflash
Part Number:CC3220SF-LAUNCHXLhow to upload a compiled code into cc3220sf-launchxl using uniflash? im not able to get upload program option on uniflash. is there a way to build a custom firmware with...
View ArticleTMS320C5505: fft frequency doesnot match with the actual signal frequency
Part Number:TMS320C5505Dear ,to calculate frequency from HWAFFT output i followed ur instructions as mentioned below by Mark Mckeown:The FFT transforms a time-domain signal into the frequency domain...
View ArticleClik here to view.
TPS65916: connection to AM5718
Part Number:TPS65916Hi everybody,we are developing a board using AM5718 + TPS659162.In particular regarding errata i862 for AM5718 we are using "Implementation 1":- AM5718 RSTOUTN is connected to PMIC...
View ArticleBQ20Z655-R1: Request for source code to automate calibration of the BQ20Z655-R1
Part Number:BQ20Z655-R1I am trying to automate the calibration of the BQ20Z655-R1 using the HPA495 BQMtester and believe that I need to request the source code to be able to achieve this?
View ArticleCCS/MSP430F2272: SPI between MSP430F2272 and the BME680
Part Number:MSP430F2272Tool/software: Code Composer StudioHello. I want to know if it is possible to connect BME680 to MSP430 microcontroller? Thanks, Oleksandra.
View ArticleCCS: MSP-FET Windows error
Tool/software: Code Composer StudioHello Everytime I connect the MSP-FET to my computer I get the Windows error that the USB device is not working correctly.I used to work with an older MSP-FET (first...
View ArticleLinux/AM5718: IPU and DSP reset fail
Part Number:AM5718Tool/software: LinuxDear team，I am running decode on am5718.The board is a custom designed.When the board booting or reload firmware，the ipu2 can not work.here is error message.Some...
View ArticleClik here to view.
LAUNCHXL-F28027F: SPI communication - Sending arrays
Part Number:LAUNCHXL-F28027FDear TI forum,I have a setup of four LAUNCHXL-F28027F. They are connected in a daisy chain trough the SPI bus. I'm using also the SYNCO of the master controller to sync the...
View ArticleCCS/RM57L843: File to program MCU via JTAG
Part Number:RM57L843Tool/software: Code Composer StudioHi,which file is used to program the MCU via JTAG? I'm asking because I want to program the MCU with a FPGA via JTAG so I want to know what file I...
View ArticleCC3120MOD: Not getting pulse on Host IRQ pin
Part Number:CC3120MODHello,I am giving RESET and nHIB pins high after power ON from host microcontroller.First, I am making RESET pin high and then after 20 ms delay, I am making nHIB pin high.I am...
View ArticleRTOS/LAUNCHXL-CC1310: Easylink Modulation with EasyLink_Phy_5kbpsSlLr
Part Number:LAUNCHXL-CC1310Tool/software:TI-RTOSHello Support Team,I want to get a bigger range with my CC1310 and so I tried to change the RADIO_EASYLINK_MODULATION for EasyLink_Phy_Custom to...
View Article