LAUNCHXL-CC1310: Reading and writing to a database tutorial.
Part Number:LAUNCHXL-CC1310I am not sure if this is the correct place to ask this but... I am working on a project for school that uses the CC1310 that involves writing and reading from a database. The...
View ArticleClik here to view.
BQ25703A: Selecting input/output with CHRG_OK while in OTG mode
Part Number:BQ25703AHello,I have a design pending centered around the BQ25703a IC and I am interested in the following;As per the evaluation board, adapter can be disconnected using CHRG_OK...
View Articlewhy ads8353 B15 is always 0?
dear sir:The project uses the ADS8353, may writes the incorrect data or the wrong time sequence when debug, now the highest bit B15 always is 0, the setting CFR B4 does not change. if replace with New...
View ArticleTPS65381A-Q1: Can [WR_CAN_STBY] SPI command let TPS65381A-Q1 to standby status?
Part Number:TPS65381A-Q1Hi, all I use TPS65381A-Q1 with RM46L852 microcontroller, In the begin, I use IGN to switch on TPS65381A-Q1 and set [IGN_PWRL] bit with 1 , so if the IGN pin go low, the...
View ArticleClik here to view.
TUSB2036: Circuit change point of three port use of USB
Part Number:TUSB2036Hello.It is the continuation of the following post.e2e.ti.com/.../2344136I tried it on a prototype.I set the NP3-pin to Low and set it to use 3 ports, all 3 ports did not...
View ArticleDP83865 support BroadR-Reach Ethernet?
Hi, I find the DP83865 can use in the Ethernet which uses four pairs of twisted-pair , but I don't sure it can be used in the Broad-Reach Ethernet which uses a pair of twisted-pair.
View ArticleLP8860-Q1: Reference design
Part Number:LP8860-Q1Hi team,In the reference design, FAULT pin(pin.11) is connected to VDDIO/EN (pin.19) through a resistor. What's the purpose?If it's for pull high function. Is it popular to connect...
View ArticleClik here to view.
TPS7B67-Q1: Controlled Adjust by MCU
Part Number:TPS7B67-Q1Dear Linear Requlators teamI will use TPS7B67-Q1 that controlled ADJ by MCU as a below.We had spec which input: 9V ~ 16V, ouput: 8V, 5V, 3.3V@200mA Can we use ADJ pin by MCU as a...
View ArticleDAC5578: The Offset error and the Gain error
Part Number:DAC5578Sir,The offset error and the gain are all measure by (12-bit: 30 and 4050; 10-bit: 12 and 1012; 8-bit: 4 and 250)For 8-bit version, what is the Offset error and the Gain error for...
View ArticleLinux/Bq24297: linbux driver
Part Number:Bq24297Tool/software: LinuxPlease tell me where to download the BQ24297 linux driver, thank you.
View ArticleClik here to view.
LVDS clock jitter cleaner for Serdes application
Hi Team,I understood CDCE813-Q1 supports LVCMOS input and can be used for the following application as jitter cleaner.Is there LVDS clock jitter cleaner that can be used for the application above?My...
View ArticleAWR1642: Meta Image Size
Part Number:AWR1642Hi expert,From AWR1642 Bootloader Flow document, the fallback image offset is 512KB (0x80000), does it mean the meta image size need to less than 512KB?• Fallback images: the...
View ArticleClik here to view.
TLV2543: Doubts about the supply voltage
Part Number:TLV2543Hi engineers,For TLV2543, the supply voltage is normally 3.3v in the datasheet, but how can I understand the words in red? Please give some direction.Regards,Jenny
View ArticleADS1014: Is possible to use ADS1014 to detect thermistor
Part Number:ADS1014My customer want to use ADS1014 to detect temp of thermistor resistor ? is it possible without other component to achieve it and what is the schematic looks like ? thanks you very...
View ArticleClik here to view.
CCS/LAUNCHXL-F28027F: XDAIS error in Code Composer Studio v7.4
Part Number:LAUNCHXL-F28027FTool/software: Code Composer StudioI already checked other posts related to the same issue but did not find a solution. Ignoring this does not help as build fails.I just...
View ArticleCCS/TMS320C6746: Ethernet Components / Getting started
Part Number:TMS320C6746Tool/software: Code Composer StudioHi. I'd like to compile a project that will include an Ethernet stack and PHY driver. I'm running into some confusion (being new to TI's...
View ArticleDS25BR440: Technical Document
Part Number:DS25BR440Dear Team,Could you help to provide below document of DS25BR440 to me? Thank you.Layout guideDesign guideReference schematicPart dimensionRegards,Jim
View ArticleADC32RF80: Questions related to sampling rate.
Part Number:ADC32RF80The sampling rate appears to be fixed at 2949.12 MSPS.Is it possible to change the sampling rate?If so, how do I change it?Which part of the data sheet should I look at?What does...
View ArticleClik here to view.
CCS/CC2640R2F: Is it possible to select relative path of SDK and TI RTOS in...
Part Number:CC2640R2FTool/software: Code Composer StudioIs there a way to feed relative path of the SDK and TI RTOS in the CCS v7.3.0.00019?My project folder sits on a repository which should also...
View ArticleTMS320DM8127: Documents of SIMCOP/LDC in DM8127
Part Number:TMS320DM8127Hi, Dear,My customer DAHUA request documents about SIMCOP LDC register in DM8127.Could you please to share it with me?They have Master NDA.Please send to sam-yu@ti.com if you...
View Article