AM3359: BBB - Ethernet Transmit Failure when Cache Enabled
Part Number:AM3359Hi,I have three applications for a single beaglebone black board:1. The linux distribution supplied on the eMMC device.2. enet_echo demo from StarterWare3. Our own ethernet stack and...
View ArticleUCC2802: VCC Rating
Part Number:UCC2802In the UCC2802 D/S, it says the absolute max. VCC rating is 12V. However, the turn-on threshold of the UCC2802 is 12.5V,typ. It looks it's not making sensing, right?and When supply...
View ArticleCCS/ADS8922B: Daisy-chain communication
Part Number:ADS8922BTool/software: Code Composer StudioHello,I am currently trying to receive conversion data from three ADS8922B set up with the daisy-chain topology. I've read the data sheet, looked...
View ArticleClik here to view.
CCS/DRA750: Stepping through u-boot after relocation
Part Number:DRA750Tool/software: Code Composer StudioHi,I am trying to debug U-boot through CCS after it relocates from the initial load address. I am following the instructions shown in the below wiki...
View ArticleCCS/EK-TM4C1294XL: Boostxl sensors GUI not showing the sensor data
Part Number:EK-TM4C1294XLTool/software: Code Composer StudioHello,I am using EK-TM4C1294XL along with BOOSTXL-SENSORS to give me temperature, humidity and light sensing data. BOOSTXL-SENSOR has...
View ArticleTMS320DM8127: NANDFLASH BOOT WITH DM8127
Part Number:TMS320DM8127Hi Dears,One of my customer asked one question about NAND FLASH BOOT.Currently they used ESMT NAND-FLASH-F59L1G81MA, and its ID is 0xC8 0xD1 0x80 0x95 0x40. As DM8127's boot...
View ArticleTS3DS26227: switch for EMMC5.1 and SD4.1
Part Number:TS3DS26227HiMy customer is requesting for switch for EMMC5.1 and SD4.1. Is TS3DS26227 suitable for this scenario? If not, could you kindly help recommend suitable solution? Thanks!RegardsDavid
View ArticleTMS320F28067: Code reads invalid memory address
Part Number:TMS320F28067Hi, Customer has some questions about read/write of memory addresses:1) If the code read an address, which is in "reversed" area, what will happen? For example the address is...
View ArticleCCS/CC2650STK: Sensortag Bluetooth examples to test.
Part Number:CC2650STKTool/software: Code Composer StudioHi,I am working on CC2650 sensor tag. I have used and tested some examples in TI Resource Explorer to test some components. I am trying to find...
View ArticleClik here to view.
AWR1642: TWS1400 lvds lane configure preblem
Part Number:AWR1642Hi, I want to use TSW1400 to store four channels data from AWR1642 . When I use the Radar stuio software it can only select the lane 1 and lane 2 to store，lane3 and lane4 is gray...
View ArticleClik here to view.
Linux/AM5728: There is no PinMux data in devicetree.txt of PinMux tool.
Part Number:AM5728Tool/software: LinuxHi Ti teamThere is no PinMux data in devicetree.txt of PinMux tool.Please fix it, thanks.
View ArticleTPS2388: TPS2388 communication issues
Part Number:TPS2388hi sir/madam: Now TPS2388EVM is connected TO the computer via USB TO GPIO(USB Interface Adapter), but the computer shows that TPS2388 has no connection (USB TO GPIO is normal)....
View ArticleLMX2595: LMX2595 Maximum Current Consumption
Part Number:LMX2595Hi TI Experts,May i know what is the maximum current, Icc needed for LMX2595?From the datasheet, it only mentioned 340mA(typical).We need to know as power consumption is critical to...
View ArticleRTOS/EVMK2H: USB for Sys/Bios(TI-PDK_k2hk) on Cortex A15_0
Part Number:EVMK2HTool/software:TI-RTOSEVMK2H(Revision 4) USB controller's ID pin is floating and not connected to PHY as per schematic. Is it possible to put USB in host mode without any hardware...
View ArticleTPS92513: about start up rise time
Part Number:TPS92513Hello E2E,I evaluating the this device on EVM.It seems like, this device has unevenness for start up rise time.I think that this cause is tolerance of gM. - gM is typically or...
View ArticleRTOS/TDA3XEVM: Sensor physical address OV10640
Part Number:TDA3XEVMTool/software:TI-RTOSHi, In bsputils_ub960.c code in VisionSDK 3.1, i had found this BspUtils_Ub960I2cParams gUb960Cfg_IMI[] = { /* IMI OV10640 1 */ {0x4C, 0x01, 0x0}, {0x58, 0x58,...
View ArticleTPS61165: About variation of VFB
Part Number:TPS61165Hi,I am considering the TPS61165 device.The purpose of use is for liquid crystal backlight.The specification is below.With current control I assume LED current of 0.2mA minimum.It...
View ArticleLM5116-12EVAL: Efficiency measurement tools used by ti.
Part Number:LM5116-12EVALDear all,I need to know what tools you used to measure efficiency of 12V, 50A buck converter module or any other module as reference.I have used several tools, but it is always...
View ArticleRTOS/AWR1642BOOST: Self chirp configuration at bootup
Part Number:AWR1642BOOSTTool/software:TI-RTOSHi,I am looking in the mmw demo, which will configure chirp parameter by itself instead of getting values from ti demo vis. app via UART and at end of...
View ArticleLAUNCHXL-CC1310: EasyLink API for HS Mode
Part Number:LAUNCHXL-CC1310Hi,I want to use a CC1310 in HS mode i.e. 4 Mbps, i see there is an PER example in sdk which has a setting and support for HS mode and it worksI don't find any example for HS...
View Article