TPS23754EVM-383: Lower Vin Reference Design
Part Number:TPS23754EVM-383Hi Support,Does TI has a reference design based on lower Vin (e.g. 15.7Vin (min))?Thanks.
View ArticleDRV10983: What is the max supported I2C speed?
Part Number:DRV10983I was unable to find the I2C speed DRV10983 supports. Does it support 400kHz?
View ArticleCCS/AM5728: IPC cause abort ()
Part Number:AM5728Tool/software: Code Composer StudioHello,I'm using Am5728 evm, SYS/BIOS, and I'm new in IPC. I created SYS/BIOS project (minimal) for C66xx core, added var Ipc =...
View ArticleTranslator for UART 5v -> 3.3v needed
Hello I need a translator for the tx-rx line. Atmega328 TX (5V) -> ESP8266 RX (3.3V).Which one should I choose. Made a selection here...
View ArticleTMS570LS1224: CAN TX not working always High
Part Number:TMS570LS1224Hi All, I am currently using TMS570LS12x Launchpad with TMS570LS1224 uC. I have configured and assigned a message object for transmission, when i scope the TX line it is always...
View ArticleTPS23861: PoE PSE with 4x TPS23861 - I2C question
Part Number:TPS23861I'm looking to develop a 16 port PoE using 4x TPS23861.I connect the SCL lines and the SDAI lines to the I2C Host.Do i then daisy chain all the AOUT and AIN through the...
View ArticleLinux/WL1831MOD: Kernel stack dump from wlcore_op_switch_vif_chanctx when...
Part Number:WL1831MODTool/software: LinuxI have several customers complaining of frequently disconnecting wifi with our devices. I have noticed that some of them have the following kernel "WARN_ON"...
View ArticleTPS2373: Using for cable longer than 100m condition
Part Number:TPS2373Hi Sir,What if I use TPS2373 in 500m cable condition? Is there any setting or component needs to be noticed?Thank you.C.T.
View ArticleCCS/ADS127L01: ADS127L01: can not get the data from ADS127L01 by spi of C5535
Part Number:ADS127L01Tool/software: Code Composer Studiohii'm using C5535 to get the data from ADS127L01 by spi interface. Now I can read the device Id reg and mode reg well from the ADS127L01. But...
View ArticleISO1541: bq76930 + ISO1541
Part Number:ISO1541Dear TI Experts,I want to use Bq76930 refer to Industrial Battery Management Module for 20S Applications Design Guide~I have seen it has used ISO1541 ,and I found ISO1541 power...
View ArticleBQ40Z50-R1: BMS total solution
Part Number:BQ40Z50-R1Hi there:I'd like to purpose a total solution , include gauge, charging, cell balance to our customer, is there any reference design or prefer solution for following...
View ArticleRTOS/TMDSLCDK138: UART Examples of PROCESSOR-SDK-RTOS-OMAPL138 don’t work
Part Number:TMDSLCDK138Tool/software:TI-RTOSHello!I got a problem with UART_BasicExample_lcdkOMAPL138_c674xExampleProject and others examples that uses UART.I installed SDK and built example without...
View ArticleDAC38RF80: 6.5Gb/s with QAM/CAP modulation on cat6a
Part Number:DAC38RF80Hello,I’m trying to design a high debit transmission line on a twisted pair cat6a. I would like to transfer data at 6.5Gb/s in the best case (may be reduce to 3.2Gb/s). The twisted...
View ArticleTDA2HG: Using GPIO pins as SPI chip select pins
Part Number:TDA2HGHi All , We are using TDA2HG in one of our designs for video processing. I have 2 queries regarding the SPI and I2C interface:1. We need to interface multiple camera companion chip...
View ArticleUCD90120A: Trouble programming UCD90120A device
Part Number:UCD90120AI have used the development board to create the programming file that I am using for the UCD90120A device on my PCB. However there is an issue with importing the configuration. I...
View ArticleCCS/TMS320F28379S: Do you have any sample code of doing the USB firmware upload?
Part Number:TMS320F28379STool/software: Code Composer StudioDo you have any sample code of doing the USB firmware upload?
View ArticleC5505 eZdsp: CHANGING CODEC CONFIGURATION / DMA TRANFERS
Hi,I have an issue.My SOC codec AIC3204 is configured at 192 Khz sampling / playback rate.I want to demodulate 42 Khz carrier DSB-SC modulated signal. I Use FFT / IFFT strategy that is very efficient...
View ArticleDRV8301-69M-KIT: Power rating of the motor development Kits
Part Number:DRV8301-69M-KITHello all!What is the power that I can draw from the DRV8301-HC-C2-KIT at 18V? The data sheet says 18V to 60V, 60A so can I draw 60A at all range of 18-60V output?In the...
View ArticleDRV8301-69M-KIT: BLDC application dev. Kit under 18V
Part Number:DRV8301-69M-KITHi All, Can I used either DRV8301-HC-C2-KIT Or DRV8301-69M-KIT below 18V? I need to develop for 4cell Lipo that means I will have 14.8V Vin in practice.
View ArticleTMDSHVMTRINSPIN: BLDC development kit voltage level 36V? 50V?
Part Number:TMDSHVMTRINSPINHello all,The voltage range of the TMDSHVMTRINSPIN is 50-350V can I use this kit for 36Vin? I have a BLDC application which I am working on and will have to use a 36V Li Ion...
View Article