Linux/AM5728: How to change SDIO Mode to High Speed(clock to 48MHz)
Part Number:AM5728Tool/software: LinuxHi all,I am trying to setup wifi module in mmc2 (mmc0,mmc1,mmc2) but I am unable to make it work with HS mode,(with clock rate above 48Mhz),With max-frequency...
View ArticleAWR1642: Can we configure the bandwidth of Loop filter in RESYNTH?
Part Number:AWR1642Hello champion, My customer want to know how they configure the bandwidth of the Loop filter in RESTNTH which is important to adjust phase noise and out-band scatter. They think...
View ArticleCCS/CC2640R2F: Issue connecting with LightBlue App
Part Number:CC2640R2FTool/software: Code Composer StudioEnvironment:simplelink_cc2640r2_sdk_1_40_00_45Code Composer Studio 7.2.0.00013SmartRF Flash Programmer 2 1.7.5PCB with CC2640R2FXDS200 USB Debug...
View ArticleTINA/Spice/AM26C32: could I get TINA TI spice model ?
Part Number:AM26C32Tool/software:TINA-TI or Spice ModelsHi, Team.i've asked be customer to get below TINA TI spice model.i was wondering if you could give me. could you ?AM26C32AM26LV31AM26C31
View ArticleIWR1443BOOST: Is it possible to improve the range resolution by adjusting ADC...
Part Number:IWR1443BOOSTAccording to the example given in Fluid-level sensing using 77-GHz millimeter wave white paper (http://www.ti.com/lit/wp/spyy004/spyy004.pdf), These posts suggest to increase...
View ArticleClik here to view.
TL4242: What does "constant current" mean?
Part Number:TL4242TL4242 is a constant current LED driver IC. I am confused by the "Constant Current".If there is a PWM input at Pin1, then the output Pin6 is PWM? If there is a shunt resistor at Pin...
View ArticleCC430F6137: Communication with cc1310 works only from cc1310 to cc430; other...
Part Number:CC430F6137Hello to all,I am currently trying to communicate between the cc430 and the cc1310. What have I done so far:After configuring all my needed radio settings (with the SmartRF...
View ArticleADS8568: in daisy chain mode
Part Number:ADS8568I have some question about ADS8568.I understand as follows. Is not there a mistake?（conditions： serial mode, daisy-chain mode using two ADS8568, using SDO_A, SDO_B, SDO_C, SDO_D,...
View ArticleTL16C752D: about LSR and FIFO questions
Part Number:TL16C752DHi Dear experts,My customer has some questions about TL16C752D, please kindly help on it!1. what is the status of LSR bit 1(RX overrun Error) when FIFO is in writing procedure?2....
View ArticleBOOSTXL-SENSHUB: replacing for BOOSTXL-SENSHUB (MPU-9250 is NRND)
Part Number:BOOSTXL-SENSHUBHello,I really like a BOOSTXL-SENSHUB based on MPU-9250. And was planned to use this sensor in my device.But TDK/Invensense not recommend this p/n for design now and...
View ArticleClik here to view.
UCC27201: How to drive high side mosfet of H bridge Buck-Boost converter...
Part Number:UCC27201I’m sorry for my poor English.I am studying H-bridge Buck-Boost converter. H-bridge Buck-Boost converter has 3 modes; Buck mode, Buck-Boost mode, Boost mode. When in Boost mode,...
View ArticleCCS/TMS320F28062F: The dimension of the connector for JTAG
Part Number:TMS320F28062FTool/software: Code Composer StudioHi TI experts.The recommend dimension for JTAG is 2.54 mm*2.54 mm. For layout reason, we want reduce to 1.27mm * 1.27mm with adaptor to...
View ArticleCCS/AWR1642: mmWave SDK Compile error
Part Number:AWR1642Tool/software: Code Composer StudioHi, I setup mmWave SDK step by step following user guide. However, when do "gmake clean" and "gmake all", it shows error as following. It...
View ArticleUSB-C SBU Pins short to GND
Hello Everybody,General question regarding the SBU-pins.We don't need the SBU pins for alternate modes. And we need to connect SBU pins to GND due to some reason.Any side effect if we connect SBU pin...
View ArticleCCS/CC1350: Crash as ordinary linux 'user'
Part Number:CC1350Tool/software: Code Composer StudioI have tried to compile some code and download the binary to SensorTag of CC1350. If I do that as 'user' in Linux, CCS will crash, if only as the...
View ArticleClik here to view.
Compiler: Cannot Install Compiler Tools
Tool/software: TI C/C++ CompilerHi everyone,Why is there an error when I install other version(15.12.6) of compiler like the figure below?Nowadays, I have take the suggestion of updating to CCS7.Some...
View ArticleClik here to view.
TPS51285B: Inductor high frequency noise issue
Part Number:TPS51285BHello, Customer meet high frequency noise of inductor. Has any comments to solve this noise issue? Thank you.BRPatrick
View ArticleCC3200-LAUNCHXL: LORAWAN implimentation
Part Number:CC3200-LAUNCHXLhi,How can i establish SPI communication between CC3200 LAUNCHXL and LORAWAN SX1272. explain me the pin connections and procedure.Thank youNaveen G S
View ArticleClik here to view.
ADS7841-Q1: Analog equivalent circuit
Part Number:ADS7841-Q1HiI'm referring SBAA178.I want to have value for C_ESD, R_SW and C_SH of ADS7841-Q1.C_IN can be referred in datasheet as C_IN = 25pF(typ) over temperature range.Can you offer...
View ArticleUSB Type-C VCONN Overvoltage Protection IC
Hi Team,Does TI have USB Type-C VCONN Overvoltage Protection IC like NCP398?http://www.onsemi.jp/pub/Collateral/NCP398-D.PDFIf the answer is yes, I would like to suggest TI part.Best Regards,Yaita /...
View Article