TPS61178: Output voltage setting - error in datasheet?
Part Number:TPS61178Hello,I have this question: in this device data sheet, there is a formula how to calculate the voltage divider. In this formula the parameter Vfb is used, this is probably the...
View ArticleCCS/CC3220S-LAUNCHXL: Cannot Connect to the Board after Updating to Uniflash...
Part Number:CC3220S-LAUNCHXLTool/software: Code Composer StudioHi,I didn't have any problems connecting to my board (CC3220S-LAUNCHXL) using Uniflash on my Ubuntu machine till this morning when I...
View ArticleClik here to view.
TXB0102: I2C_TEST
Part Number:TXB0102Hi Dear,I have a question about my project listed below.It is need to design level shifter between FPGA and DUT. The DUT will be I2C device. Voltage level (Vccb) from FPGA is set to...
View ArticleTPS53355: Ripple Generation Values Question
Part Number:TPS53355Hello Team,I'm looking for some further insight into how the ripple generation values should be chosen based on the design example in the datasheet. These calculations don't match...
View ArticleTMDSADAP180TO100: 180 to 100 Pin DIMM Adapter - Datasheet
Part Number:TMDSADAP180TO100Hi everyone!I am missing more information and dataheet from TMDSADAP180TO100. Someone of you have used this board?I have a micro-controller (F28379D) with 180 pin, but my...
View ArticleCCS/MSP430G2553: Setting the DCO to 100 KHz approximately.
Part Number:MSP430G2553Tool/software: Code Composer StudioHi,I want to set DCO to about 100 KHz. I have pasted code below. The code is not working as it should. I have one more doubt, does CPU starts...
View ArticleClik here to view.
TPS54240: coupled inductor
Part Number:TPS54240HelloI got this PSU design around the TPS54240, basically it is the same design shown on the app.note SLVA369A (http://www.ti.com/lit/an/slva369a/slva369a.pdf), that uses this DC...
View ArticleTPS54620: Connecting two DCDC in series
Part Number:TPS54620Hello I would like to connect two DCDC in series: 12V input -> DCDC1 converts to 5.5V output - >goes to second DCDC input and converts to 3.3V outputAre there any pitfalls or...
View ArticleCCS/CC2650: Sharing Project
Part Number:CC2650Tool/software: Code Composer StudioHi all,I made some changes to the SimpleBlePeripheral and I am trying to port it to a different PC. The project is working, but when it is imported...
View ArticleTDA2SX: Cost effective alternative to Vision EVM Kit for short term usage
Part Number:TDA2SXHi,We've finalized TDA2x for our product design and our 1st spin of boards are expected to be out in few months from now. Meanwhile, in order to get some hands-on with the SDK (Linux...
View ArticleCCS/DRV8301-69M-KIT: DRV8301-69M compatibility with F28035
Part Number:DRV8301-69M-KITTool/software: Code Composer StudioHi TI experts,I have bought a DRV8301-69M recently and realized that it has F28069M control card which does NOT support InstaSpinBLDC. Can...
View ArticleAM3358: System clock and Functional clock
Part Number:AM3358Could any one suggest me :-Is System clock and Functional clock both are same ? I want to set prescaler value to obtain 12 Mhz frequency for I2C2 and In AM335x TRM section no....
View ArticleClik here to view.
DRV8886: Issue with the driver
Part Number:DRV8886Hi, I am attaching my design here. It is not giving me anything in the output. Currently that 100u cap is not in place since I do not have it now, I guess that should not be the...
View ArticleTSW14J10EVM: Incompatibility between KC705, TSW14J10EVM, and ADC32RF45EVM
Part Number:TSW14J10EVMHello,I am working with a system that utilizes the KC705, TSW14J10EVM, and ADC32RF45EVM to process an analog system with custom FPGA firmware. I have found that many of the JESD...
View ArticleCC85XXDK: Default PurePath software for the Master and Slave EMs?
Part Number:CC85XXDKI am starting to work with the CC85XX design kit and will shortly start to look at the PurePath Wireless Configurator. So that I don't end up with a bricked module if I make an...
View ArticleLM5023: Output Voltage
Part Number:LM5023Which parameters should I be tweaking to get an output voltage Vout = 22.1 and I out = 4.9A.I have set the over current protection at 22.1 Vout
View ArticleClik here to view.
SN74LVC1G14-Q1: Clarity on Application Speeds
Part Number:SN74LVC1G14-Q1Hello,Looking through the datasheet on page 10, Section 9.1:The device is used for buffer type functions where the input is slow or noisy, but also states that this device is...
View ArticleClik here to view.
CCS/TMS320F28032: How the heck do you add files into a project into a...
Part Number:TMS320F28032Tool/software: Code Composer StudioI read the wiki on adding files, right clicked project -> add files, selected the files and it won't let me chose where to add it. Instead...
View ArticleMSP432P401R: I2C working but very slow (122.5 hz)
Part Number:MSP432P401RI am having a weird problem with my I2C configuration. It is running REALLY slow! It is working as expected, but just not at the speed expected. Its clock is at 122.5hz. My SMCLK...
View ArticleLinux/AM3352: Issue with WiLink 8 WiFi / SDIO driver integration with latest...
Part Number:AM3352Tool/software: LinuxTeam,I am receiving reports from my customer that the WiLink8 integration may be broken in the latest SDK 4.0 for the Sitara AM3352 (BZCE60) with respect to the...
View Article