DS16EV5110A: Holds Clock Low?
Part Number: DS16EV5110ATeam,Does the device ever extend clock cycles for a message by holding the clock low? Can you please confirm whether the device holds the clock low and any details if it does?...
View ArticleTPS63070: pls recommend the most suitable solution for buck boost
Part Number: TPS63070Hi Team,pls recommend the most suitable solution for buck boost for below condition,1. Vin min~3.5V2. Vin max ~ 15V3. Vout 3.5~5V4. Iout max 2.5A~3A5. switching frequency >...
View ArticleClik here to view.
DRV8873: how to maximum the DRV8873's current ability?
Part Number: DRV8873Hi,customer use DRV8873 to drive motor whose normal current 3.5A and starting current is more than 10A, the IC reset again and again.their setting and SCH is as below:my question...
View ArticleClik here to view.
INA199: AC Current sensing with Current transformer
Part Number: INA199Hello,I've tried to use INA199A1 for measuring the AC current sensing using the Current transformer, and I've attached the schematic from google source. Now, I'm receiving output...
View ArticleAM5728: Patch for usb camera in sdk4.3
Part Number: AM5728Hi,https://e2e.ti.com/support/processors/f/791/p/523614/2023362#pi316653=1&pi320966=2As mentioned in the above link, TI has already given a patch to solve VPE driver which needs...
View ArticleCC3220SF-LAUNCHXL: Azure Plugin lp_monitor_demo build errors?
Part Number: CC3220SF-LAUNCHXLHi,I am getting this build error with the lp_monitor_demo. How do I resolve this error?cannot set 'connectionPolicy' to (0,1,0,0),(1,0,0,0)When I open the sysconfig file...
View ArticleTRS3232E-Q1: HALF DUPLEX setting
Part Number: TRS3232E-Q1Hi TI-teamMy customer wants to use TRS3232E-Q1 in half duplex.Can it be used with a half-duplex line ?Please answer the following questions when available.1.What should the...
View ArticleAWR1843: Why MCAN_TDCR register TDCO bits are set to 8 in Mmwave_SDK test code?
Part Number: AWR1843Hi,Why MCAN_TDCR register TDCO bits are set to 8 in Mmwave_SDK test code?It become SSP (Secondary Sampling Point) 100% on 40MHz Xtal and data phase rate 5 Mbps.
View ArticleADS1015: offset error in FSR=4.096
Part Number: ADS1015Dear expert,May I learn from you the offset error in single-end FSR=4.096?I only find offset error as +/-0.25 LSB in FSR=+/-2.048 in datasheet *Electrical...
View ArticleLM25066: Higher Voltage Device
Part Number: LM25066Dear Team,The customer is evaluating LTC4281.Our LM25066 Vin range is not enough compare to LTC4281.Do you have any road map device that I am not aware of?Or what is the suitable...
View ArticleCC2642R: Are we able to upgrade the BT SDK from 4.2 to 5.0 via OAD?
Part Number: CC2642RHi there, I would like to ask if our initial build for this board is based on SDK for BT4.2, will we be able to upgrade to BT5.0 SDK via OAD in the future?Thanks,Peter
View ArticleClik here to view.
DRV8306: Couldn't start normally
Part Number: DRV8306Hi TeamMy motor couldn't start up normally using myself DRV8306 board. But If i use hand to touch motor, Maybe it can start to run. Do you has any suggestion how can I run it? I...
View ArticleTMS320F28377S: desoldering HLQFP-176P in factory
Part Number: TMS320F28377SHi expert,Do you have any advice and how to re-work HLQFP-176P package F2837x in factory? This may including desoldering and soldering. Any guideline from TI or third party...
View ArticleClik here to view.
CC2652R: CC2652 latest V3.30 SDK simple peripheral project IAR compiler...
Part Number: CC2652RHi Team,CC2652 SDK V3.30, default simple peripheral project, debug mode, no modification. Using IAR.This one takes too much memory. Configure it to release mode,...
View ArticleWEBENCH® Tools/TPS54541: Webench results do not match calculations
Part Number: TPS54541Tool/software: WEBENCH® Design ToolsIn reaction to a customer request, I have created my own spreadsheet based on the datasheet for calculating the compensation of the TPS54541....
View ArticleClik here to view.
MSP430F425: Can I know the differences between below two markings: REV G and...
Part Number: MSP430F425Hi TI Experts Can I know the differences between below two markings?I‘d like to know the meaning and difference between REV G and REV IThank you very much
View ArticleTPS2812: ESD HBM spec consult
Part Number: TPS2812Hi team,It is nice to know you here. My customer needs ESD HBM specs of this device to set up their database. Thanks.
View Articleam5728 linux gstreamer
hello,The platform chip that I use is am5728. I want to know that how to use gstreamer to finish the H264 encode of RAW8 image data? In the multimedia chapter of PROCESSOR SDK LINUX，I see the content...
View ArticleTUSB320: TUSB320 apply question
Part Number: TUSB320Hi：We encountered some problems in the process of applying TUSB320 and need to ask.We don't have EC and battery, so the TUSB320's SMBUS doesn't have a host, we use GPIO mode, so how...
View ArticleClik here to view.
CC2640R2F: FW Upgrade fail via UART Bootloader
Part Number: CC2640R2Fhiwe have an issue about using the Smart RF programmer2 to do the UART I/F FW upgrade, some chips work well, but some chips got the chance of "Timed out waiting for ACK/NAK..."do...
View Article