Placing vector table at application start address via sys/bios .cfg file.
Hello Friends,I recently took over a Sys/BIOS project targeting the Tiva TM4C1294CPDT device and need to add Firmware Upgrade support to the application.We are using your app note: USB Serial Device...
View ArticleTPS61165 connection configuration
Hello LED ForumWe are doing a design where the customer has the flexibility of choosing between different LCD panels. As a result the back-light LED configuration may change from 9 string 1 row, 6...
View ArticleAM335x Implementing MDIO Bitbang Driver For Clause 45
Hello,I'm working on a custom board where I have an AM335x with an MDIO/MDC bus connected to a gigabit ethernet phy (Marvell 88E1510) and a 10-gigabit ethernet phy (Marvell 88X2222P). I am using a...
View ArticleUsing the USB 2.0 OTG PHY on Deca Max10 board
Hi,I'm using the Deca Max10 FPGA evaluation kit. The kit consists of an USB 2.0 OTG PHY which uses the Texas Instruments TUSB1210 transceiver chip fro data transfer. I want to use the USB 2.0 OTG to...
View ArticlePCM5310 I2S Input and Output
Hello,Does the PCM5310 support I2S for all 4 inputs and all 4 outputs?Thank you,Jared
View ArticleTX-SDK-1 questions
I have some questions regarding the TX-SDK-1. I am working on a proprietary device, and I would prefer not to discuss in a public forum.Please send me a message at your earliest convenience. Thanks for...
View ArticleCC3200 HTTP server example
Hi,I am working on a CC3200 Launchpad connected to a WINDOWS 10 machine. I opened the http_server example project on the CCS & connected to the board successfully. My jumpers are on P58-Vcc for AP...
View ArticleSmartRF06+CC1310 frequency hopping example?
Are there any examples that use frequency hopping for the SmartRF06+CC1310 development kit?I believe the example in sink/sensor example that comes the TI 15.4 stack uses frequency hopping(?), but it's...
View ArticleLaunchpad C2000 flashing problem
Hi,I have a starnge problem.When I am running from CCS Ver 6.2 -> in debug mode the code is running perfectHowever - when I flash it (after starting debugger) or in standmode using UniFlash - it is...
View ArticleSN74AHC1G125 Output Short Circuit Duration
On parts like the Quad Bus Buffer SN74125 (not the SN74LS125A) there is a Short Circuit Output Current (Ios) parameter that states the output current when a gate being shorted. On the SN74125 a single...
View ArticleBQ28Z610 - Golden file and programming without EV2300
Hi TI Community,I am preparing to perform learning cycle for 1s4p configuration of UR18500F cells (Chem ID = 0107), but I have some questions.I know exact model of cells, but configuration is 1s4p not...
View ArticleCCS loads CPU 45%
HelloMy CCS loads CPU 45% while designing application. There are many actions in Progress tab ("Refreshing paths and symbols", "Linking viewer selection..."), they appear and disappear very fast so I...
View ArticleClik here to view.
Antialias filtering and RFI protection ADS1299
Hi,Talking about the onchip digital decimation filter, page 20 of the datasheet says "This ΔΣ converter feature drastically reduces the complexity of the analog antialiasing filters typically required...
View ArticleMSP430Ware_3_60_00_10_setup does not run.
Hi,I am using CCS 6.2.0 on Window 10Now I am trying to install MSP430Ware, but the setup file does not do anything. Even when I ran it as administrator.I already disabled virus software, but still same...
View ArticleClik here to view.
Fatal error #1965 MSP430
Hello All,I got an example code for the SIGFOX technology, but I compile the code without modifying anything and I got the error #1965 cannot open source file bsp.hHow do I fix this error?Thankyou
View ArticleWrite to I/O pin in fewest number of clock cycles
I am trying to write to a standard MSP430 I/O pin in the fewest number of clock cycles possible. Obviously for a single pin I can only drive a 1 or 0. The fastest that I've been able to write to these...
View ArticleAn Issue about Selecting one of ADS131xxx ADC family
hiI'm already using Analog Devices AD7606 and AD7770 ADCs for smart grid IEDs application.I looked to the TI cross references and found that the ADS131xxx family is proper substitution for Analog...
View ArticleCCS V6 has build problems with dsk6416 project built in CCS V3.1
Hi,I had a project with dsk6416 evaluation board from Spectrum Digital working on CCS 3.1. When I had to change my OS to windows 7 I contacted them to advise and they recommended CCS V6. After...
View ArticlebqStudio problems
Yesterday, I was running bqStudio (1.3.52) on a Windows 7 system. For the most part it seemed to work OK, but I had problems with certain operations. I noticed that I had installed it to D: which was...
View Articlequestion about BQ25892
Hi,I will use BQ25892 in our new project, I have one question about it.if it can work with battery fuel gauge BQ27531-g1, and if not, please recommend any battery fuel gauge to work with BQ25892.Thank...
View Article