Part Number:CC2640R2F
Tool/software:TI-RTOS
Hello,
In the ProjectZero example, I am trying to set the OSAL SNV to use 2 sectors since I am using GPCache as RAM.
In the stack project predefines I've set OSAL_SNV=2
However, in the Memory Allocation tool, I see that only 1 sector is allocated to the snvSector.
I'm calling it close on total flash usage but I should still have 6KB free. (possibly not contiguous)
Could this be due to the .ccfg using the last page of Flash? Attached below is my cc26xx_app.com linker file.
Thank you for your time!
Brett
/******************************************************************************
@file cc26xx_app.cmd
@brief CC2650F128 linker configuration file for TI-RTOS with Code Composer
Studio.
Imported Symbols
Note: Linker defines are located in the CCS IDE project by placing them
in
Properties->Build->Linker->Advanced Options->Command File Preprocessing.
CACHE_AS_RAM: Disable system cache to be used as GPRAM for
additional volatile memory storage.
CCxxxxROM: Device Name (e.g. CC2650). In order to define this
symbol, the tool chain requires that it be set to
a specific value, but in fact, the actual value does
not matter as it is not used in the linker control
file. The only way this symbol is used is based on
whether it is defined or not, not its actual value.
There are other linker symbols that do specifically
set their value to 1 to indicate R1, and 2 to
indicate R2, and these values are checked and do make
a difference. However, it would appear confusing if
the device name's value did not correspond to the
value set in other linker symbols. In order to avoid
this confusion, when the symbol is defined, it should
be set to the value of the device's ROM that it
corresponds so as to look and feel consistent. Please
note that a device name symbol should always be
defined to avoid side effects from default values
that may not be correct for the device being used.
ICALL_RAM0_START: RAM start of BLE stack.
ICALL_STACK0_START: Flash start of BLE stack.
PAGE_AlIGN: Align BLE stack boundary to a page boundary.
Aligns to Flash word boundary by default.
Group: CMCU, SCS
Target Device: CC2640R2
******************************************************************************
Copyright (c) 2013-2017, Texas Instruments Incorporated
All rights reserved.
Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions
are met:
* Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
* Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
* Neither the name of Texas Instruments Incorporated nor the names of
its contributors may be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
******************************************************************************
Release Name: simplelink_cc2640r2_sdk_1_40_00_45
Release Date: 2017-07-20 17:16:59
*****************************************************************************/
/*******************************************************************************
* CCS Linker configuration
*/
/* Retain interrupt vector table variable */
--retain=g_pfnVectors
/* Override default entry point. */
--entry_point ResetISR
/* Suppress warnings and errors: */
/* - 10063: Warning about entry point not being _c_int00 */
/* - 16011, 16012: 8-byte alignment errors. Observed when linking in object */
/* files compiled using Keil (ARM compiler) */
--diag_suppress=10063,16011,16012
/* The following command line options are set as part of the CCS project. */
/* If you are building using the command line, or for some reason want to */
/* define them here, you can uncomment and modify these lines as needed. */
/* If you are using CCS for building, it is probably better to make any such */
/* modifications in your CCS project and leave this file alone. */
/* */
/* --heap_size=0 */
/* --stack_size=256 */
/* --library=rtsv7M3_T_le_eabi.lib */
/* The starting address of the application. Normally the interrupt vectors */
/* must be located at the beginning of the application. Flash is 128KB, with */
/* sector length of 4KB */
/*******************************************************************************
* Memory Sizes
*/
#define FLASH_BASE 0x00000000
#define GPRAM_BASE 0x11000000
#define RAM_BASE 0x20000000
#define ROM_BASE 0x10000000
#ifdef CC26X0ROM
#define FLASH_SIZE 0x00020000
#define GPRAM_SIZE 0x00002000
#define RAM_SIZE 0x00005000
#define ROM_SIZE 0x0001C000
#endif /* CC26X0ROM */
#ifdef AUX_AS_RAM
#define AUX_RAM_BASE 0x400E0000
#define AUX_RAM_SIZE 0x800
#endif /* AUX_AS_RAM */
/*******************************************************************************
* Memory Definitions
******************************************************************************/
/*******************************************************************************
* RAM
*/
#ifdef CC26X0ROM
#if CC26X0ROM == 2
#define RESERVED_RAM_SIZE 0x00000C00
#elif CC26X0ROM == 1
#define RESERVED_RAM_SIZE 0x00000718
#endif /* CC26X0ROM */
#endif /* CC26X0ROM */
#define RAM_START RAM_BASE
#ifdef ICALL_RAM0_START
#define RAM_END (ICALL_RAM0_START - 1)
#else
#define RAM_END (RAM_START + RAM_SIZE - RESERVED_RAM_SIZE - 1)
#endif /* ICALL_RAM0_START */
/*******************************************************************************
* Flash
*/
#define FLASH_START FLASH_BASE
#define WORD_SIZE 4
#ifdef CC26X0ROM
#define PAGE_SIZE 0x1000
#endif /* CC26X0ROM */
#ifdef PAGE_ALIGN
#define FLASH_MEM_ALIGN PAGE_SIZE
#else
#define FLASH_MEM_ALIGN WORD_SIZE
#endif /* PAGE_ALIGN */
#ifdef CC26X0ROM
#define PAGE_MASK 0xFFFFF000
#endif /* CC26X0ROM */
/* The last Flash page is reserved for the application. */
#define NUM_RESERVED_FLASH_PAGES 1
#define RESERVED_FLASH_SIZE (NUM_RESERVED_FLASH_PAGES * PAGE_SIZE)
/* Check if page alingment with the Stack image is required. If so, do not link
* into a page shared by the Stack.
*/
#ifdef ICALL_STACK0_START
#ifdef PAGE_ALIGN
#define ADJ_ICALL_STACK0_START (ICALL_STACK0_START * PAGE_MASK)
#else
#define ADJ_ICALL_STACK0_START ICALL_STACK0_START
#endif /* PAGE_ALIGN */
#define FLASH_END (ADJ_ICALL_STACK0_START - 1)
#else
#define FLASH_END (FLASH_START + FLASH_SIZE - RESERVED_FLASH_SIZE - 1)
#endif /* ICALL_STACK0_START */
#define FLASH_LAST_PAGE_START (FLASH_SIZE - PAGE_SIZE)
/*******************************************************************************
* Stack
*/
/* Create global constant that points to top of stack */
/* CCS: Change stack size under Project Properties */
__STACK_TOP = __stack + __STACK_SIZE;
/*******************************************************************************
* GPRAM
*/
#ifdef CACHE_AS_RAM
#define GPRAM_START GPRAM_BASE
#define GPRAM_END (GPRAM_START + GPRAM_SIZE - 1)
#endif /* CACHE_AS_RAM */
/*******************************************************************************
* Main arguments
*/
/* Allow main() to take args */
/* --args 0x8 */
/*******************************************************************************
* ROV
* These symbols are used by ROV2 to extend the valid memory regions on device.
* Without these defines, ROV will encounter a Java exception when using an
* autosized heap. This is a posted workaround for a known limitation of
* RTSC/rta. See: bugs.eclipse.org/.../show_bug.cgi
*
* Note: these do not affect placement in RAM or FLASH, they are only used
* by ROV2, see the BLE Stack User's Guide for more info on a workaround
* for ROV Classic
*
*/
__UNUSED_SRAM_start__ = 0x20000000;
__UNUSED_SRAM_end__ = 0x20005000;
__UNUSED_FLASH_start__ = 0;
__UNUSED_FLASH_end__ = 0x1FFFF;
/*******************************************************************************
* System Memory Map
******************************************************************************/
MEMORY
{
/* EDITOR'S NOTE:
* the FLASH and SRAM lengths can be changed by defining
* ICALL_STACK0_START or ICALL_RAM0_START in
* Properties->ARM Linker->Advanced Options->Command File Preprocessing.
*/
/* Application stored in and executes from internal flash */
FLASH (RX) : origin = FLASH_START, length = (FLASH_END - FLASH_START + 1)
/* CCFG Page, contains .ccfg code section and some application code. */
FLASH_LAST_PAGE (RX) : origin = FLASH_LAST_PAGE_START, length = PAGE_SIZE
/* Application uses internal RAM for data */
SRAM (RWX) : origin = RAM_START, length = (RAM_END - RAM_START + 1)
#ifdef CACHE_AS_RAM
GPRAM (RWX) : origin = GPRAM_START, length = GPRAM_SIZE
#endif /* CACHE_AS_RAM */
#ifdef AUX_AS_RAM
AUX_RAM (RWX) : origin = AUX_RAM_BASE, length = AUX_RAM_SIZE
#endif /* AUX_AS_RAM */
}
/*******************************************************************************
* Section Allocation in Memory
******************************************************************************/
SECTIONS
{
.intvecs : > FLASH_START
.text : >> FLASH | FLASH_LAST_PAGE
.const : >> FLASH | FLASH_LAST_PAGE
.constdata : >> FLASH | FLASH_LAST_PAGE
.rodata : >> FLASH | FLASH_LAST_PAGE
.cinit : > FLASH | FLASH_LAST_PAGE
.pinit : >> FLASH | FLASH_LAST_PAGE
.init_array : > FLASH | FLASH_LAST_PAGE
.emb_text : >> FLASH | FLASH_LAST_PAGE
.snvSectors : > FLASH (HIGH)
.ccfg : > FLASH_LAST_PAGE (HIGH)
GROUP > SRAM
{
.data
// #ifndef CACHE_AS_RAM
.bss
.vtable
.vtable_ram
vtable_ram
.sysmem
.nonretenvar
} LOAD_END(heapStart)
.stack : > SRAM (HIGH) LOAD_START(heapEnd)
#ifdef CACHE_AS_RAM
reorganized_into_gpcache
{
icall.obj(.data)
icall.obj(.bss)
device_information.obj(.data)
notification.obj(.data)
request.obj(.data)
spectrum_data.obj(.data)
SRI_Global.obj(.data)
CommandHandler.obj(.data)
RFCC26XX_singleMode.obj(.bss)
} > GPRAM
// .bss :
// {
// *eeprom_base(.bss)
// } > GPRAM
// .data :
// {
// *(.data)
// } > GPRAM
// GROUP > GPRAM
// {
// .data
// }
// .bss :
// {
// *(.bss)
// } > GPRAM
#endif /* CACHE_AS_RAM */
#ifdef AUX_AS_RAM
reorganized_into_auxram
{
sdi_task.obj(.data)
sdi_task.obj(.bss)
sdi_rxbuf.obj(.bss)
sdi_tl_uart.obj(.bss)
sdi_tl.obj(.bss)
sdi_tl.obj(.data)
} > AUX_RAM
#endif/* AUX_AS_RAM */
}