Part Number: ADS1191
(Please visit the site to view this file)
In our custom board(IMX6ULL) we used ads1191-16bit ADC SPI interface , The Driver for the same is being probed but when we read ADC value the output is zero even though giving (2V to 3.3V for AIN(4th pin)) when reading from the userspace using IOCTL call .
Kernel Version:4.1.1
dts declaration is,
&ecspi1 {
status = "okay";
pinctrl-names = "default";
fsl,spi-num-chipselects = <1>;
pinctrl-0 = <&ecspi1_pins>;
ads1191dev@0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&printer2t_pins_default>;
compatible = "ads1191_ADC";
reg = <0>;
spi-max-frequency = <512000>; /* 16M */
};
};
ecspi1_pins:ecspi1_pins_default {
fsl,pins = <
MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x70a1
MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x79
MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x70a1
>;
};
printer2t_pins_default: printer2t_pins {
fsl,pins = <
MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x79
>;
};
Getting below dmesg while inserting the driver.....
Value Read... ff 00 00 00
Msb2Lsb ... ff 00 00 00
.......Ads1191 ID in INIT= 255
.......Ads1191 ID = 255
Value Read... ff 00 00 00
Msb2Lsb ... ff 00 00 00
.......Ads1191 ID = 255
Ads1191 ID Not Matched/Device not Detected
Ads1191 LOFF = 255
- Reg Read...
>>>>>>ads1191 detect success<<<<<<<
Getting below dmesg when calling ioctl function....
Division by zero in kernel.
CPU: 0 PID: 815 Comm: test33V2 Not tainted 4.1.15-2.0.1+gb63f3f5 #75
Hardware name: Freescale i.MX6 Ultralite (Device Tree)
[<80015d78>] (unwind_backtrace) from [<8001271c>] (show_stack+0x10/0x14)
[<8001271c>] (show_stack) from [<8082d360>] (dump_stack+0x84/0xc4)
[<8082d360>] (dump_stack) from [<802b1418>] (Ldiv0+0x8/0x10)
[<802b1418>] (Ldiv0) from [<8063c12c>] (ads1191_user_ioctl+0x54/0x80)
[<8063c12c>] (ads1191_user_ioctl) from [<800fb204>] (do_vfs_ioctl+0x3e8/0x608)
[<800fb204>] (do_vfs_ioctl) from [<800fb458>] (SyS_ioctl+0x34/0x5c)
[<800fb458>] (SyS_ioctl) from [<8000f480>] (ret_fast_syscall+0x0/0x3c)
adcval value in ioctl=0
I am attaching driver ads1191.c , please go through them and the error log ,suggest me if any software and Hardware changes are required.